Search results for query: *

Bought this thing for $250, it ran and drove but the radiator had rotted out from it sitting. Specs were: poorly swapped in 302, np435, dana 21 9 inch rear, 44 front Built a rear bumper for it Drove it for a while. The rear end made a lot of noise, so I swapped a spooled and 4.56 geared...

Anyone ever notch their transmission pan for driveshaft clearance? I'm just trying to be a cheapass and avoid going the two-piece d-shaft route. It's a th350/np205, I need to chop about an inch out of the pan

My fancy :bling: braided fuel line has rotted out from the inside, and pisses gas out everywhere in the middle of the line. Anyone else have this sort of problem, or did I just get a lemon hose? Line is only a few years old.

It's time for me to go fast(ish kinda:redneck:), plus it's time for my pile of 'yota to be thrown away. This will be using a lot of recycled yota parts, or parts that are laying around from other piles that have been scrapped. My old man is also starting to become interested in wheeling, so I'll...

Looking at buying a 2008 KTM 250sx. However, IIRC, after the two-stroke ban in 2006(?), all two strokes sold can only be used on closed courses, as you can not buy tabs for them? Is this correct? Or is my memory out of whack? Probably going to try to buy the bike either way, it just may be a...

How far can I safely lean my engine back? Haven't actually put a angle finder on it yet, but this looks like it's 10-15 degrees back. Trying to get the front driveshaft under the clutch fork.

Ran across this thing while I was out looking for a diesel pickup. Not quite what I was planning on buying, but what the hell, price was right and it will tow anything I need it to. 94 Ford L7000, 5.9 cummins, 5/2 speed, 5' sleeper, 11' bed w/5th wheel, 260xxx miles, picked it up for 3 grand...

Anyone heading up to Evans on Saturday. Lookin for a group to tag along with

My first customer job :cheer: He needed a new x-member to clear his driveshaft after his sas and lift. Sorry for the shitty pics, I'll try and get some better ones once he has it powdercoated. Started at 930 last night, finished around 4 this morning:redneck: The victim Trying to tig...

Went to roll the yota into the shop to put it on the lift so I can run the brakelines. SM465 tranny is not in gear but is FULLY locked up. Had to put the t-case in nuetral to get the **** to roll. What would cause this? I've personally never ran this tranny(bought it from Odie a couple/three...

Drug this thing out of the bushes a couple weeks ago for another rebuild.:rolleyes: Getting rid of some of the ghetto fab(more like making prettier ghetto fab:haha:) Anyways, it got another axle swap, took 1 inch of body lift out(I'd like to get rid of it all but it's not worth it to redo...

Will the rear yoke off my ford's 205 ('78 stuck to a np435 if it matters) fit on my chev's 205('78 stuck to a sm465). I know the input splines are different but what about the outputs?

Here's what I have: 2 1000 watt rms subs 2 1000 watt rms amps 2 capacitors With the goal being not to burn my truck to the ground, what's the best way to wire this stuff up? I'm thinkin 0-2 guage wire to a distribution block, 4 gauge out to the capacitors, 4 gauge in/out of the amps and to...

Threw this together for a friend who is a cheap/lazy bastard:redneck:. Uses most the stock parts for now, although he will upgrade the suspension and steering links when he gets there inboarded links, had to do a little grinding on the chassis to clear Cut the stock springs (be sure to...

Bought this thing when I was 18. I didn't know any better :redneck: 460/np435, built 9" and dana 44, 42s, super stiff suspension, typical mall crawler bolt ons that broke everytime I tried driving through a puddle:puke: Decided I'm not gonna finish the truggy anytime soon, so I'm making...

Anyone else running these yet? I ditched my claws to try a set of these and IMO they seem to do much better. The thicker outer lugs and bigger center lugs seem to help them grab harder then the claws:cool:

I've been looking at crawlers for a while now, but being a nitro guy, I wasn't sure that the crawler would keep me entertained for long. When I saw the RTR however, I was sold. At least that way if it became a dust collector, I was only $350ish out. I figured there are a few people that are in a...

What's the :cool: budget-ish notcher these days? I'm gettin tired of using a cutoff wheel and a grinder:redneck:

I'm going to order my AX10 this weekend and start to get into RC crawling. Just wanted to know what the common mods were. Seems like high clearance and inboarded links are high on the list. What works? What doesn't?

I'm about to order the coilovers for the yota, and I can't decide what springs I want. Here's the specs: chevy 350 w/alum. heads, sm465, 205, will have a 10or12,000lb winch on the front, and lots of tube. Here's a pic to show how the weight is centered. They will be dual rate, 18" travel...