Search results for query: *

I'm looking for a dual power steering pump set up for a 1.6 geo tracker motor. Or if someone has a link so I can look at a setup I may can build me one. Also what rear steer valve do you recommend. I looked at the Psc manual valve but want more of a budge frendly one.

1.6L tracker motor w/ got propane kit. Motor does not smoke, leak or burn oil. comes with 2 propane tanks 5 speed manual tranny 6.5:1 transfercase with ZOR craddle gm altenator psc pump blue top optima Front axle: toyota front axle 5.29 gears,spool longfeild 30 spline axles arp...

I'm looking for a 4.0 motor to put back in my 88 jeep cherokee

78 ford f150 front has been narrowed 7" 95 model 351 windsor fuel injected motor freshly rebuilt C6 trans with RMVB 205 transfer case that is twin sticked dana 60 front with 4.88 lockrite 806 joints 35 spline stubs with drive flanges trussed 14 bolt rear 4.88 welded trussed with disk brakes 4...

i am looking for a set of tubes to put in my 44" tsl's. where does everyone buy there tubes at and what size or kind do i look for?

i have a buddy that is wanting to sell his cab truck to fund his bronco project so he has a rig more suitable for his family. specs are: 78 ford f150 front has been narrowed 7" 95 model 351 windsor fuel injected motor freshly rebuilt C6 trans with RMVB and b&m shifter 205 transfer case that is...

does anyone run them in our rigs? i have some of my tires that i cannot get the vulcanized part to hold, so i thought about running a boot and put a tube in it. i just did not know if they will hold up to running them at the tire pressure we run at. its on 44 tsls with a 15" wheel and the wheel...

need a 44 tsl for 15" wheel with 80% or more tread or if you have a pair i might buy both

i have a 7/8 and 3/4 cnc series 705 tall master cylinder they have been on one ride then swapped to a different size asking $120 for the pair

first trip out in my rig and the front lockrite is slipping very bad, so what is everyone running with good luck been thinking detroit. its going in a chevy d60

good game did anyone else see tebow crying like a beeoch

i have started getting ready to paint the wicked yj just looking to see what everyone ones to get the rust off the cage to get it ready for paint it is just surface rust.i have been looking at trying ospho has anyone else tryed it or should i just sand it :dunno:

looking for a good straight cj hood (price and pics would be good if anyone has one) email is [email protected]

s10 extended cab with full exo cage 15 gallon aluminum fuel cell gauges included(3 3/8 tack 2 5/8 oil, water and volts) 2 four point harness steering orbital 14" bilstine remote res shocks new 42 tsls on 15" beadlocks chevy 60 SRW 4.56 gears open 14 bolt SRW 4.56 gears welded, disk brakes with...

your driveshaft, what is the smallest size to run does not look like i am going to have a lot of room up front and was seeing if anyone runs about a 2" shaft also where does everyone get the tabs for mounting like body panels and dask looking for something already threaded thanks

i have a np 205 with the adapter for a turbo 400 asking $500 obo

i have 8 left hand thread and 8 right hand thread 2 1/2 johnny joints with all the jam nuts asking $650 obo

i need a 350 turbo transmission case the internals dont have to be good since my trans was new just broke the back half off it so if anyone has one close that would be great i live close to the bama, tennessee and mississippi line

what is the deal with them bought the magazine back in october and have yet to see one in the mail. anyone else have the problem i tried to go to the internet site but it will not come up so who do i call or what is going on its starting to piss me off :****:.

i have been thinking about getting some suspension seats for my rig since i have had to go under the knife cause of a broken hip i want something a little easier on my hip and back, i was wandering what brand and style of seat everyone likes have been looking at the corbeau ultra wide or maybe a...