Menu
Forums
New posts
Search forums
Calendar
Monthly
Weekly
Agenda
Archive
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Help Support Hardline Crawlers :
Forums
Rock Crawling Forums
General Discussion
Cold vulcanizing from Busted Knuckle Off Road
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="ToledoDan" data-source="post: 745013" data-attributes="member: 13704"><p>Had to buy the 650g kit because i could not find the 300g kit. cost about $142 shipped +tax. I have a $10 off coupon code that can be used by 2/19 LURG-3JDV-8AVX</p><p>Followed BK's video. A couple things I learned along the way, a cheap or old toothbrush will spread the primer just fine. It's about the same consistency of the same blue color locktite. it will drip inside the hole. if thats going to kick your ocd into overdrive, put something down inside the tire to absorb it. A flap disk on a 4inch grinder will work just fine. used a 1/4" tap in a pencil grinder to round the end of the opening. before putting the primer on, lay each tube the length of the cut AND taper. this is about how much product you need. twist like video. I put a zip tie around the twist before cutting to keep the remainder of the product from oozing out. you won't squeeze this stuff out of the sleeve. dont try. just cut the sleeve lengthwise and pull the plastic off it best you can. thankfully i am in SE Houston and it was almost 70° today. in light of some of the bad cold weather related experiences i read about, i put the small heater in the garage for tonight, Already 73° in there, but it's not supposed to drop below 59° tonight.</p></blockquote><p></p>
[QUOTE="ToledoDan, post: 745013, member: 13704"] Had to buy the 650g kit because i could not find the 300g kit. cost about $142 shipped +tax. I have a $10 off coupon code that can be used by 2/19 LURG-3JDV-8AVX Followed BK's video. A couple things I learned along the way, a cheap or old toothbrush will spread the primer just fine. It's about the same consistency of the same blue color locktite. it will drip inside the hole. if thats going to kick your ocd into overdrive, put something down inside the tire to absorb it. A flap disk on a 4inch grinder will work just fine. used a 1/4" tap in a pencil grinder to round the end of the opening. before putting the primer on, lay each tube the length of the cut AND taper. this is about how much product you need. twist like video. I put a zip tie around the twist before cutting to keep the remainder of the product from oozing out. you won't squeeze this stuff out of the sleeve. dont try. just cut the sleeve lengthwise and pull the plastic off it best you can. thankfully i am in SE Houston and it was almost 70° today. in light of some of the bad cold weather related experiences i read about, i put the small heater in the garage for tonight, Already 73° in there, but it's not supposed to drop below 59° tonight. [/QUOTE]
Insert quotes…
Verification
Post reply
Latest posts
Meet Christine Reborn, my trail bouncer build
Latest: ridered3
Yesterday at 10:44 PM
Tech & Fab
Golden Mountain Off-road Park opening
Latest: ridered3
Yesterday at 10:40 PM
General Discussion
W
3800 sc and 60*bellhousing 700r4
Latest: wrenchbender
Yesterday at 7:36 PM
Off Road 4x4 Parts For Sale
For Sale
1999 Jeep Cherokee
Latest: Big David
Yesterday at 3:56 PM
Vehicles For Sale
For Sale
Jimmy Smith Rockbouncer 383 Stroker
Latest: ToledoDan
Yesterday at 3:49 PM
Vehicles For Sale
Forums
Rock Crawling Forums
General Discussion
Cold vulcanizing from Busted Knuckle Off Road
Top