Menu
Forums
New posts
Search forums
Calendar
Monthly
Weekly
Agenda
Archive
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Help Support Hardline Crawlers :
Forums
Rock Crawling Forums
Tech & Fab
Never ending Samurai build...
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="clemsonjeep" data-source="post: 652856" data-attributes="member: 6317"><p>Making small strides...</p><p></p><p>Picked up a trans pan from a Toyota Previa at the pullapart so i could rob the dipstick from it and swap it to my pan to move it to the driver side. Hoped to use the whole pan but turns out the Tracker has a deeper pan. Then I used a combination of upper dipstick tubes to put together one that worked for me.</p><p></p><p><img src="http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170407_153215295_zpsodgk8wpu.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p><img src="http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170408_180605942_zpsabzsfkex.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /> </p><p></p><p>Got the Winters shifter hooked up. Since my driveshaft is so close to the pan I couldn't use the parts Winters sends. I had to flip the shifter arm on the trans upright and the cable to come out the front of the shifter. The cable goes down through the original shifter hole down the driver side of the trans, loops back to the rear then around to the passenger side. In this configuration the shifter is pushing the cable from P thru 1st rather than pulling as it would in the standard configuration.</p><p></p><p><img src="http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170408_131649412_zpscrxdcnca.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p>The next concern is how close the driveshaft gets to the line fitting at the rear corner of the trans. I'll be hitting pullapart again tomorrow since I'd noticed some Jeeps or Toyotas used banjo style fittings which would suck this up closer to the case.</p><p></p><p><img src="http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170407_192522036_zpsikxlfkhi.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p>Part of the 4spd swap was to have the slip yoke for the intermediate shaft machined so it would fully engage the output shaft. I dropped it off at a local machine shop this week and 2 days later I picked this up...</p><p></p><p><img src="http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170406_143205829_zpso7d7oapr.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p></blockquote><p></p>
[QUOTE="clemsonjeep, post: 652856, member: 6317"] Making small strides... Picked up a trans pan from a Toyota Previa at the pullapart so i could rob the dipstick from it and swap it to my pan to move it to the driver side. Hoped to use the whole pan but turns out the Tracker has a deeper pan. Then I used a combination of upper dipstick tubes to put together one that worked for me. [IMG]http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170407_153215295_zpsodgk8wpu.jpg[/IMG] [IMG]http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170408_180605942_zpsabzsfkex.jpg[/IMG] Got the Winters shifter hooked up. Since my driveshaft is so close to the pan I couldn't use the parts Winters sends. I had to flip the shifter arm on the trans upright and the cable to come out the front of the shifter. The cable goes down through the original shifter hole down the driver side of the trans, loops back to the rear then around to the passenger side. In this configuration the shifter is pushing the cable from P thru 1st rather than pulling as it would in the standard configuration. [IMG]http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170408_131649412_zpscrxdcnca.jpg[/IMG] The next concern is how close the driveshaft gets to the line fitting at the rear corner of the trans. I'll be hitting pullapart again tomorrow since I'd noticed some Jeeps or Toyotas used banjo style fittings which would suck this up closer to the case. [IMG]http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170407_192522036_zpsikxlfkhi.jpg[/IMG] Part of the 4spd swap was to have the slip yoke for the intermediate shaft machined so it would fully engage the output shaft. I dropped it off at a local machine shop this week and 2 days later I picked this up... [IMG]http://i292.photobucket.com/albums/mm13/clemsonjeep/Samurai/IMG_20170406_143205829_zpso7d7oapr.jpg[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Latest posts
I am moving to Tennessee
Latest: Kubotaorange76
Today at 8:48 AM
General Discussion
For Sale
2005 Ford Excursion Eddie Bauer
Latest: jeeptj99
Yesterday at 11:55 AM
Vehicles For Sale
I.w.i.w clampy
Latest: bobbedrunner99
Friday at 4:44 PM
Tech & Fab
Salvage 10
Latest: ridered3
Friday at 7:47 AM
Tech & Fab
Ultra4 - Battle in Bluegrass (Bowling Green, KY) East Series (4/19-4/20)
Latest: ridered3
Thursday at 12:01 PM
Trail Rides & Competitions
Forums
Rock Crawling Forums
Tech & Fab
Never ending Samurai build...
Top