• Help Support Hardline Crawlers :

Search results for query: *

  • Users: EddieHall
  • Content: Threads
  • Order by date
  1. EddieHall

    Left over build parts

    Ls K1 forged crankshaft 3.622 stroke was installed and ran on dyno went to a stroker. Yukon dana 44&35 hubs Wilwood metric calipers,pads Ballistic fabrication dana 60 shave kit Barnes 4x4 dana 60 tie rod ends Holley digital dash cover can't remember were I got it form Holley dominator ecu mount...
  2. EddieHall

    Yukon hardcore hubs dana 44

    Brand new Yukon hardcore dana 44 or 30 hubs 250.00 shipped plus 3% PayPal fee Eddie 850 382-4209 Pensacola Fl
  3. EddieHall

    Sold

    Sold thanks hardline
  4. EddieHall

    Left over build parts winch,ls harness,ls3 heads,atlas adapter

    Brand new Warn VR8 narrowed 2" comes with cable and synthetic wire rope 400.00 New used to mock up th350 to atlas transfercase adapter 120.00 Westcoast ls3 cylinder heads brand new stainless valves double springs decked .20 I have the build sheet on the heads 600.00 Ls1/Ls6 cut down harness...
  5. EddieHall

    King 2.5 bumps with cans

    Brand new bumps changed plans... 2.5 x 4inch king bumps with cans Make offer Plus 2.9% PayPal fee And shpping Location Pensacola Thanks eddie 8503824209
  6. EddieHall

    New Yukon 35 spline dana 60 drive flanges

    Going with Yukon locking hubs on the front instead Never installed, just removed the caps to polished them 200.00 shipped 2.9% PayPal fee Eddie 8503824209
  7. EddieHall

    Yukon hardcore hubs dana 44 19 spline

    Brand new never used .decided not to SAS my tacoma 220 shipped 2.9%PayPal fee Eddie 8503824209
  8. EddieHall

    Sold thanks hardline

    Sold,to BamaReno :dblthumb:
  9. EddieHall

    Warn winch narrowing

    So I got bored today and torn my warn vr8 winch down .reasoning do to a tight fit between the frame rails. total time to narrow was about an hour or so. Narrowed up 2" I machined the weld off the splined hub,then the drum end plate weld off,cut 2" off the tube welded back together.simple to do...
  10. EddieHall

    Finally heading to the powder coater

    I'd thought this day would never come. Almost 2 years to this point I hope the the final install goes faster.
  11. EddieHall

    Sold/Expired Yukon Dana 60

    Out of box.. Type in yukon dana 60
  12. EddieHall

    Bump stop spacing wit Ori's

    Ok so this prolly has been covered be for . Looking for advise,suggestions or thoughts. I'm setting up the bump cans.looking for info for how much space between the bump and pad. Chassis is a rock bouncer 20" ori struts they have around 7-8" of compression 4" travel bumps Rite now I have it...
  13. EddieHall

    Ls3 injectors from magnuson tvs2300 supercharger

    They came with the supercharger went with 100lb .from what I've read these are 63lb. not 100% sure the paperwork says there flowed for 5 minutes at 65psi.just what the tag says... I also have the magnuson fuel rails if someone wants them make offer 100.00 shipped plus 3%PayPal fee Thanks eddie...
  14. EddieHall

    Left over parts king bumps,ls msd plug wires, trans cooler

    King bump stops purchased on here a month ago brand new I need 2.0 trade for 2.0 or 400.00 shipped Please add 2.9% PayPal fee thanks Eddie 8503824209
  15. EddieHall

    Sold

    Sold
  16. EddieHall

    Ebay yukon dana 60 ujoint 199.99 obo

    Hell of a deal it's for a pair...
  17. EddieHall

    Autometer cobalt gauges

    Autometer 5" monster cobalt tach, with shift light Water temperature - manual sender Volt - electrical Fuel level - electrical Oil pressure- manual Transmission temp- electrical All gauges r new never hooked up just taking out of packing All the hardware that comes with gauges is there...
  18. EddieHall

    Ls engine parts fast102,prc heads ,etc,

    Prc heads sold Fast 102 LXR intake with 42lbs EV1 fast injectors brand new, fast fuel rails PTM 102MM throttle body r used.. with idle hole drilled.. 1200.00 shipped Edelbrock ls1-ls6 style timing cover was removable cover plate for easy cam swaps. For non front cam sensor 150.00 shipped...
  19. EddieHall

    Sold/Expired Trickflow ls steam line kit

    Trickflow ls steam line kit Most parts r unused the 4 an fittings were bolted on the engine 60$ shipped + 3% PayPal fee Thanks Eddie 8503824209
  20. EddieHall

    A+ vendor Tripp @ Skinny pedal racing

    Great guy to do business with, quick to call,email,text back.. Thanks for the rcv's front and rear best price by hundreds on each set!! I'll be doing alot more business with you soon im sure.. Thanks Eddie. Maybe 1 day I'll get it finished

Latest posts

Top