• Help Support Hardline Crawlers :

Highlighted posts from Tuesday, Apr. 13, 2021

HCBot

Member
Staff member
Joined
Mar 1, 2021
Messages
15
Click here to view on the web
We're continuing to include products from across the web that members are talking about most. These products link to our partner, Primary, who has been helping us test new ways of showing forum content.​
Products Hardline Crawlers members are discussing
Note: We may earn an affiliate commission if you purchase through the guide, but they include the most talked-about products even if we don't earn anything. View more products on our partner's site, Primary.
March 31, 2021 · Summit Racing Equipment · 569.5800 USD​
Tech & Fab​
FlatlandFSJ said - I'm not sure on whats best, or whos better. I have used the safecraft 3 nozzle system on the builds I've done recently, up to the owner for the last word, but i strongly recommend ...
April 5, 2021 · Summit Racing Equipment · 16.0300 USD​
Tech & Fab​
87TPIYJ said - I'm running mine off the output to the cooler at the transmission. Use one of these and a shorty sending unit. Normally runs 160-180° can hit 210° on long climbs or beat downs. ...
Highlighted posts
April 07, 2021 * 13 posts * 536 views
Bodacious said: What are your guys' thoughts on these transmissions? Any experience with them? I have a Th350 I'm sending out to PTC, but came across these transmissions online also and was curious ... Read more >>
April 12, 2021 * 9 posts * 210 views
ridered3 said: Normally I'd say we are up for a Memorial Day weekend camping trip, but may have to sit this one out (or make it just a day trip) depending on how everyone is feeling. Read more >>
April 10, 2021 * 5 posts * 157 views
poolman said: My wife wants a mall crawler. I know there were some years that had issues. What years? And what do I need to look out for? Thanks Read more >>
April 11, 2021 * 5 posts * 301 views
Markrobinson said: 1995 Nissan Pathfinder XE V6 (reman engine with less than 5k miles) 5 speed 3.96:1 Calmini geared transfer case 99-04 Dana 60 front axle (chromos, 35 spline outers, drive flanges, ... Read more >>
April 12, 2021 * 5 posts * 156 views
tcDawg said: This winch is driving me nuts. Needs some help. Warn VR 8000 with regular solenoids. It stopped spooling out a few months ago. I pulled the solenoid box off and jumpered the motor ... Read more >>
April 08, 2021 * 5 posts * 382 views
Dan_Goodwin said: Up for sale is an EXCELLENT condition 2003 Ford Ranger Edge Plus 2wd with a 3.0 V6. The mileage is an honest 53k and the condition shows. Truck has been senior adult owned and ... Read more >>
April 12, 2021 * 2 posts * 75 views
cjtrucking said: Im looking for a set of jk, jl, or jt axles, preferably locked 4.10-4.88. Preferably no trusses because they arent going under a jk, jl, or jt. Closer to knoxville, TN the better. ... Read more >>
April 12, 2021 * 2 posts * 53 views
poolman said: I tried to edit my first post but couldn't figure it out. I'm looking for some Rockwell pattern wheels or H1s that I can re center. 16"-16.1"-16.5"-17" Read more >>
April 08, 2021 * 3 posts * 255 views
bronco2bcn said: One Dana 60hp axle out of 88 f350. Rear is a 14 bolt cab and chassis rear.front is narrowed to 64 inches rear is 63.5 wide.these are basically bolt spring over axles for a yj or ... Read more >>
April 12, 2021 * 3 posts * 100 views
Scott F. said: King Kutter brand, 72" wide deck. Side discharge. Wheels on all four corners so it will glide over uneven lawn surfaces. I just knocked off the surface rust and put on a fresh ... Read more >>

Continue reading...
 

Primary

HardlineCrawlers Assistant
Here are some related products that HardlineCrawlers members are talking about. Clicking on a product will take you to HardlineCrawlers’s partner, Primary, where you can find links to HardlineCrawlers discussions about these products.

 
 

Latest posts

Top