jprider
Let's Ride!
CopperHead Tube Chassis Buggy
Fuel injected Gm 350 chevrolet,has angle plug heads,roller rockers
Chassis is all dom besides under the cab,under the cab is 2x3.
New rod,main,cam bearings with new rings. Just had heads reworked, Trans rebuilt, and a new JB Fab Cable Twin Stick.
Its a .040 over motor with huge domes never new exact comp. X rods *i think*. Crank was turned .010. Vette double humps and intake Are ported and matched. Heads intake and block have been decked. Gaskets must be the exact ones on it. Also all new seals etc. Pete jackson quiet gear drive, vette water pump bout brand new. 1.6 roller rockers and hardened push rods, baffled oil pan, Holley fuel pump
2.02 1.60 valves. It likes timing but not too much. Has fox air shocks
Newly rebuilt GM 60 front welded with chromoly outters and chromoly drive flanges with new artek truss/skid plate.
14 bolt rear with factory detroit locker. 4:56 gears
Drive shaft built by Chattanooga Driveline with lifetime warranty, strongest, smallest he could build.
Fresh rebuilt Th350 with GM np205 w/new seals and bearings twin sticked,trans has good clutches.
3/4" and 5/8" heims all moving and suspension parts have grade 8 bolts
40x16x17 New Super Swampers (2rides) on New 17" Marsh Racing Beadlocks w/rock Rings!
All new spicer u joints
Disc brakes all the way around with stainless steel lines and Wilwood pedal assembly.
Kirkey seats with covers, g force harnesses
Custom headers
Custom aluminum fuel cell
Custom aluminum radiator equivalent to a 4 core with big fan, dont remember cfm's but does its job never gets hot
Floor pans and dash
Full PSC 2.75" hydraulic steering, Eaton orbital and fittings, new lines, 8" double ended ram with High Steer and Double shear kit from Artek Mounted on there skid pan
Sidewinder shifter.
Lots of other extras.
$23,500
Located around Pickwick Lake 38357
Send a message and I can TXt Videos and more Pics
Fuel injected Gm 350 chevrolet,has angle plug heads,roller rockers
Chassis is all dom besides under the cab,under the cab is 2x3.
New rod,main,cam bearings with new rings. Just had heads reworked, Trans rebuilt, and a new JB Fab Cable Twin Stick.
Its a .040 over motor with huge domes never new exact comp. X rods *i think*. Crank was turned .010. Vette double humps and intake Are ported and matched. Heads intake and block have been decked. Gaskets must be the exact ones on it. Also all new seals etc. Pete jackson quiet gear drive, vette water pump bout brand new. 1.6 roller rockers and hardened push rods, baffled oil pan, Holley fuel pump
2.02 1.60 valves. It likes timing but not too much. Has fox air shocks
Newly rebuilt GM 60 front welded with chromoly outters and chromoly drive flanges with new artek truss/skid plate.
14 bolt rear with factory detroit locker. 4:56 gears
Drive shaft built by Chattanooga Driveline with lifetime warranty, strongest, smallest he could build.
Fresh rebuilt Th350 with GM np205 w/new seals and bearings twin sticked,trans has good clutches.
3/4" and 5/8" heims all moving and suspension parts have grade 8 bolts
40x16x17 New Super Swampers (2rides) on New 17" Marsh Racing Beadlocks w/rock Rings!
All new spicer u joints
Disc brakes all the way around with stainless steel lines and Wilwood pedal assembly.
Kirkey seats with covers, g force harnesses
Custom headers
Custom aluminum fuel cell
Custom aluminum radiator equivalent to a 4 core with big fan, dont remember cfm's but does its job never gets hot
Floor pans and dash
Full PSC 2.75" hydraulic steering, Eaton orbital and fittings, new lines, 8" double ended ram with High Steer and Double shear kit from Artek Mounted on there skid pan
Sidewinder shifter.
Lots of other extras.
$23,500
Located around Pickwick Lake 38357
Send a message and I can TXt Videos and more Pics