Search results for query: *

I had the same problem - finally came up with a set that looked like this after some gentle cleaning: 9 23 6B3 603817 2 - is there a date or other code scratched on the gears (though I doubt they are stock)? My ultimate solution was http://www.riversidegear.com/ Call them up with what you have...

Excellent - YotaRunner - esitmate price for labor and a parts kit, sir - including pulling the tranny out, etc. Throwing in a new clutch may be a good idea, too. Let me know if that gets way outside the scope of work you have time for.

If anyone can rebuild this for my stepfather or knows of a good shop to do the work, I'd be very grateful. Here's the skinny: 1987 Toyota 5 speed, 22R engine, 4x4 I have the VIN if that will help anyone. So - let me know your opinions on local shops you all have used, please, or if you can...

There is still a Pawn Shop in Redmond, it's adjacent to where the old T&D Feeds used to be, across from one corner of Redmond Town Center. Here you go - lots of them. Don't forget that the building which housed the Church of Scientology there on Bel-Red and 56th. is now a Cash Co.. No, the...

Anyone have one of these? Diacro bender model #DB8073 I'm presuming that it's like these models: http://www.diacro.com/diacro_products/diacro_power_bender.html However, I've not seen it just yet so wanted to check to see if anyone has one that I can see pictures of so that I know what...

I've got a set of axles off of an old Wagoneer that had a QuadraTrack case in it - what I'm thinking of doing, instead of grinding the housing a 1/2" is having the long side of the axle tube shortened a 1/2" - is that even possible?

That's more than reasonable. Get the welded-through clevis setup and make sure that you pickup the mounts for the winch, too. Good find!

I'd be lying if I said I could tell the difference. Since the thing had no top cover on it when I got it from the guy... Looking at it, it seems like the 2nd. gear synchronizer gear is ALWAYS in contact with the lower idler gears?? I'll shoot pictures tonight and post them up so that you can...

I'm rebuilding an SM420 4 speed. Having followed the directions from Novak with their kit, i'm starting a what I believe to be a properly assembled transmisison, but I can't seem to make first or 4th. work correctly.. I'll post pictures tomorrow. Is anyone here good with these transmissions...

http://www.sunrayengineering.com/

[minor redirect] I have a 230 Volt Little Giant solvent pump if anyone needs it, I'll make you a good deal - I needed a 120V and failed to note the voltage on the eBay auction... [/minor redirect]

Howdy, welcome to the board! If you don't have the Rockwells yet, you may be well-advised to consider somewhat more standard fare in axles. Dana 60's can likely be narrowed by many folks with professional tools and time - and in this case, it can be done right. IMO, Rockwells won't drive well...

Haiku by Outback...

I've actually got a Dana 18 with a Warn Overdrive in my garage right now waiting for me to finish my Front Dana 44 rebuild so that I can take it on. Last I struggled with a Pinion nut I found that if I took a propane torch and heated that nut up for 3 to 5 minutes I could then hit it with the...

To the best of my knowledge that IS a 205 :) It's got the nut on this side for the idler gear and the 3 (or 4) bolt cover on the other side on the other side of the idler gear shaft. Divorced setup it looks like - funky outputs.. What is it out of? A 203 would have that doubler box on the...

pressing bearings in and out for all the crap that I seem to be rebuilding for the Jeep of late: Axles, transmission, transfer case.

Could not find one around to rent, so I just bought one :)

Looking for a good used press, anyone know of where I can get one? Thanks! Brett.

I tried to buy parts for my parts washer the other day, but they had just been acquired by SafetyKleen and were not selling individual parts at that time. I found the pump I needed on eBay (Little Giant), but it's not 100% match. Who do you folks use to service your Parts Cleaners?

FC is Forward Cab, I believe. MB was for Military Body - no doors, no tailgate, etc. I <3 my beat-up old YJ!