Search results for query: *

  1. R

    Sold/Expired Super duty 4.88's and 5.13's

    Re: Re: Super duty 4.88's and 5.13's Delivered today, just as u said. Thanks. Here's a bump.
  2. R

    Sold/Expired 2 Bilstein 5125's, 12" travel SOLD

    Re: If DoWork don't want them, I'll take them. Pay pal ready.
  3. R

    Sold/Expired Esab Plasma Cutter, brand new.

    Re: Sold...
  4. R

    Sold/Expired Esab Plasma Cutter, brand new.

    Esab PowerCut 400. Dual voltage. Cuts 3/8", severs 1/2". This is brand new. Only opened the box to gawk at it and make sure it was complete. Still have the open warranty card for registration. This unit IS BRAND NEW sent to my door directly from Esab, never been hooked up. I plan to...
  5. R

    Sold/Expired '12 7x20 Car hauler trailer SOLD

    Re: Re: '12 7x20 Car hauler trailer Ok, thanks. It was worth a shot Sent from my SCH-I545 using Tapatalk 2
  6. R

    Sold/Expired '12 7x20 Car hauler trailer SOLD

    Re: Re: '12 7x20 Car hauler trailer Any chance ur sellin because u want to downsize to a 7x14? ;D Sent from my SCH-I545 using Tapatalk 2
  7. R

    Sold/Expired tj axles front and rear complete 4.10 gears $300

    Re: Re: Re: tj axles front and rear complete 4.10 gears $300 that's a yj. Tj is coil sprung on all four corners Sent from my SCH-I545 using Tapatalk 2
  8. R

    Sold/Expired tj axles front and rear complete 4.10 gears $300

    Re: Re: Re: tj axles front and rear complete 4.10 gears $300 Tj.... Sent from my SCH-I545 using Tapatalk 2
  9. R

    1350 CV measurement needed please

    Re: Re: Re: 1350 CV measurement needed please Pm'd u back bud. It's just a u joint. You can have it if you like. I got all 1310's... Sent from my SCH-I545 using Tapatalk 2
  10. R

    Welding on High Steer Arms???? Morris Mountain owners

    Re: Re: Welding on High Steer Arms???? Morris Mountain owners One more thing.... if possible, I would try and avoid MIG welding to cast. Yeah, it works, but stick welding it would provide much better penetration, and nickel rods (Made for cast) are much easier to come by over nickel MIG...
  11. R

    Welding on High Steer Arms???? Morris Mountain owners

    Re: Re: Welding on High Steer Arms???? Morris Mountain owners My opinion, I think its going to depend on how much you weld and what kind of force that weld will see. If its just a small tab to help the high steer arm, I should be ok if you to alittle preheating, and peen it afterwards. And...
  12. R

    1350 CV measurement needed please

    Re: Re: 1350 CV measurement needed please I've got a 1350 joint in my tool box you can have. I got no use for it. Atleast I was told it was, and it looks right. Im off Western and 640 Sent from my SCH-I545 using Tapatalk 2
  13. R

    Sold/Expired Jeep 4.0l engine and 8.25 axle

    Re: Re: Jeep 4.0l engine and 8.25 axle Bump Sent from my SCH-I545 using Tapatalk 2
  14. R

    Sold/Expired Jeep 4.0l engine and 8.25 axle

    Removed from a 2000 xj with 180k on the clock. Jeep ran strong for the little bit I drove it. Bought the jeep for parts and this is what's left. The engine was rebuilt back in June-ish and has approximately 1800 miles on the rebuild. Comes as pictured below. Asking $800, obo. 8.25 rear...

Latest posts

Back
Top