Menu
Forums
New posts
Search forums
Calendar
Monthly
Weekly
Agenda
Archive
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Help Support Hardline Crawlers :
Forums
Rock Crawling Forums
Tech & Fab
5.3 won't start
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Draco" data-source="post: 194272" data-attributes="member: 479"><p>This is the way I did my adjustments and it fired right up. (after days of cussing and throwing ****.)</p><p></p><p>Worth a try... <img src="/styles/default/xenforo/smilies2/dunno.gif" class="smilie" loading="lazy" alt=":dunno:" title="Dunno :dunno:" data-shortname=":dunno:" /></p><p></p><p>Here are step by step instructions:</p><p></p><p>Remove the valve cover.</p><p></p><p>Identify the number one cylinder. See the page on Firing Order on the menu to the right if you are not sure which cylinder is number one.</p><p></p><p>Turn the engine over until you see the number one cylinder exhaust valve rocker arm JUST START to move from the closed position to open. You may need to turn the motor over a couple of times to reach this point, but do not turn any further.</p><p></p><p>Locate the intake valve.</p><p></p><p>Loosen the rocker arm adjustment nut until you feel some obvious lash or clearance in the adjustment.</p><p></p><p>Using the thumb and index finger of one hand, grasp the intake push rod below the rocker arm, and rotate it back and forth (clock-wise and counter clock-wise successively to be sure there is no remaining pressure on the push rod from the rocker arm as you loosen the rocker arm adjusting nut.</p><p></p><p>Using the other hand, while continuously performing step 6, with a 5/8 socket and ratchet, tighten the rocker arm adjustment nut slowly until you feel a resistance of motion on the push rod.</p><p></p><p>This will be the zero lash adjustment point. For hydraulic lifters, tighten the rocker arm adjustment nut 3/4 of a turn. For solid lifters, back off the rocker arm adjustment nut until your feeler gauge just fits under the contact point between the valve stem and the rocker arm. Fine tune the adjustment by checking it with a feeler gauge just slightly thicker than the preferred clearance to be sure the clearance is not greater than it should be. If the larger feeler gauge will fit, it needs to be re-adjusted. A lash tolerance of 1-2 thousandths of an inch in the valve adjustment for solid lifters would be acceptable since it may be difficult for someone who is in-experienced to be more precise than that.</p><p></p><p>Turn the engine over until the intake valve opens and then is almost closed.</p><p></p><p>On the exhaust valve, repeat steps 5 through 8 for the exhaust valve adjustment.</p><p></p><p>Repeat this procedure for each cylinder. Be sure to do each cylinder sequentially, either following the firing order, following the cylinders numerically, or in the case of a V8 doing one side of the engine at a time. I prefer to do one side of the engine at a time.</p></blockquote><p></p>
[QUOTE="Draco, post: 194272, member: 479"] This is the way I did my adjustments and it fired right up. (after days of cussing and throwing ****.) Worth a try... :dunno: Here are step by step instructions: Remove the valve cover. Identify the number one cylinder. See the page on Firing Order on the menu to the right if you are not sure which cylinder is number one. Turn the engine over until you see the number one cylinder exhaust valve rocker arm JUST START to move from the closed position to open. You may need to turn the motor over a couple of times to reach this point, but do not turn any further. Locate the intake valve. Loosen the rocker arm adjustment nut until you feel some obvious lash or clearance in the adjustment. Using the thumb and index finger of one hand, grasp the intake push rod below the rocker arm, and rotate it back and forth (clock-wise and counter clock-wise successively to be sure there is no remaining pressure on the push rod from the rocker arm as you loosen the rocker arm adjusting nut. Using the other hand, while continuously performing step 6, with a 5/8 socket and ratchet, tighten the rocker arm adjustment nut slowly until you feel a resistance of motion on the push rod. This will be the zero lash adjustment point. For hydraulic lifters, tighten the rocker arm adjustment nut 3/4 of a turn. For solid lifters, back off the rocker arm adjustment nut until your feeler gauge just fits under the contact point between the valve stem and the rocker arm. Fine tune the adjustment by checking it with a feeler gauge just slightly thicker than the preferred clearance to be sure the clearance is not greater than it should be. If the larger feeler gauge will fit, it needs to be re-adjusted. A lash tolerance of 1-2 thousandths of an inch in the valve adjustment for solid lifters would be acceptable since it may be difficult for someone who is in-experienced to be more precise than that. Turn the engine over until the intake valve opens and then is almost closed. On the exhaust valve, repeat steps 5 through 8 for the exhaust valve adjustment. Repeat this procedure for each cylinder. Be sure to do each cylinder sequentially, either following the firing order, following the cylinders numerically, or in the case of a V8 doing one side of the engine at a time. I prefer to do one side of the engine at a time. [/QUOTE]
Insert quotes…
Verification
Post reply
Latest posts
Pickett State Park/Blackhouse Mountian 1-23-2016
Latest: ridered3
Yesterday at 3:12 PM
Trail Rides & Competitions
Daves Offroad Supply
Latest: Daves Offroad Supply
Wednesday at 10:52 AM
Vendors
B
For Sale
Artec Back-bone truss for 14 bolt
Latest: Bebop
Tuesday at 7:19 PM
Off Road 4x4 Parts For Sale
P
YouTube of the day
Latest: paradisepwoffrd
Monday at 8:21 AM
General Discussion
Cash LeCroy Illness
Latest: ridered3
Sunday at 2:58 PM
General Discussion
Forums
Rock Crawling Forums
Tech & Fab
5.3 won't start
Top