Menu
Forums
New posts
Search forums
Calendar
Monthly
Weekly
Agenda
Archive
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Help Support Hardline Crawlers :
Forums
Rock Crawling Forums
Tech & Fab
Bobbing a Yota bed
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Paulie" data-source="post: 857269" data-attributes="member: 15969"><p>ill explain what i did. first i found the seem by the tailgate that runs in between the bedsides. use a cut-off wheel and cut that seem out, looks like it might have silcone on the seem (i had no idea what it was). cut that seem and after that if you look behind your tail light youll follow that same seem flow around your tail light bucket. i just basically cut an inch behind the whole tail light bucket. then ran that diagonal to the seem at the tailgate. youll see what im talking about if you look. cut the floor first then work on the sides. i fallowed a perfect line on mine, not sure if youll have the same. i had inner fenders that screwed to my bedsides, exactly not sure the proper name. anyways i fallowed that down to the flor cuts and back half was off. where it was cut sand it flat (eyeballing) and measure 14" or however you choose and dow the sides first this time. floor is alittle harder to get measured right. my way is hard to explain but i measured back from the tailgate cut up 14" that would be my new cut to mate the floor together. i can post lots of pics to show you what im talking about. check in the am</p></blockquote><p></p>
[QUOTE="Paulie, post: 857269, member: 15969"] ill explain what i did. first i found the seem by the tailgate that runs in between the bedsides. use a cut-off wheel and cut that seem out, looks like it might have silcone on the seem (i had no idea what it was). cut that seem and after that if you look behind your tail light youll follow that same seem flow around your tail light bucket. i just basically cut an inch behind the whole tail light bucket. then ran that diagonal to the seem at the tailgate. youll see what im talking about if you look. cut the floor first then work on the sides. i fallowed a perfect line on mine, not sure if youll have the same. i had inner fenders that screwed to my bedsides, exactly not sure the proper name. anyways i fallowed that down to the flor cuts and back half was off. where it was cut sand it flat (eyeballing) and measure 14" or however you choose and dow the sides first this time. floor is alittle harder to get measured right. my way is hard to explain but i measured back from the tailgate cut up 14" that would be my new cut to mate the floor together. i can post lots of pics to show you what im talking about. check in the am [/QUOTE]
Insert quotes…
Verification
Post reply
Latest posts
2-2.5 ton Rockwell’s new in crates
Latest: Piros 1
Today at 2:42 AM
Off Road 4x4 Parts For Sale
For Sale
Jeep TJ tube buggy for sale $32,000.00
Latest: Piros 1
Today at 2:41 AM
Vehicles For Sale
T
For Sale
85-91 Ford Kingpin Dana 60 $2k
Latest: truck-oholic
Yesterday at 3:58 PM
Off Road 4x4 Parts For Sale
Pluging holes
Latest: baldduck74
Wednesday at 3:56 PM
General Discussion
Trail gear hydro assit on a toyota
Latest: baldduck74
Monday at 12:27 PM
General Discussion
Forums
Rock Crawling Forums
Tech & Fab
Bobbing a Yota bed
Top