Menu
Forums
New posts
Search forums
Calendar
Monthly
Weekly
Agenda
Archive
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Help Support Hardline Crawlers :
Forums
Rock Crawling Forums
Tech & Fab
CB Antennea Cable Splice?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Jacob" data-source="post: 1470633" data-attributes="member: 19630"><p>3 foot increments is a myth, I don't care where you read it.</p><p></p><p>It is a myth that deals with the velocity factor of coax and trying to acheive a zero voltage point in the wavelength of 36' at 27.4 Mhz.</p><p></p><p>There are a lot of variables that come into play with that zero voltage point, so many that it would be virtually impossible to maintain it. These factors are the actual channel you are transmitting on, the type of coax used (RG 58 or RG 8x), the quality of the coax, etc. In most cases this zero voltage point will be achieved around 12' if using average quality RG58, but once again this will vary due to more of the above mentioned variables. This zero voltage point is such a moving target and so insignificant when compared to other components of the system that it should not be considered to be top of list of priorities, or even close to the top.</p><p></p><p>Use the amount of coax it takes to reach from your radio to your antenna base. Concentrate more on grounding, antenna location, and tuning your antenna length for SWR.</p><p></p><p>There is a level of loss when dealing with connectors in coax which is usually around .5 db per connection. In my opinion that is a fair trade off for not having to tear your roof apart to run new cable. I would splice it using two UHF connectors and use another piece of matching coax of RG58 or RG8x, whatever is there now. Make sure you have a quality antenna, good grounds, good ground plane for the antenna, and your antenna is adjusted for SWR.</p><p></p><p>In the end it is your stuff and your choice to believe what you want from the internet or books.</p><p></p><p>I am no expert in radio or CB systems, but I was a radio tech in the Army and a senior field technician for Motorola for 5 years if you are wondering where I came up with all of this ****.</p></blockquote><p></p>
[QUOTE="Jacob, post: 1470633, member: 19630"] 3 foot increments is a myth, I don't care where you read it. It is a myth that deals with the velocity factor of coax and trying to acheive a zero voltage point in the wavelength of 36' at 27.4 Mhz. There are a lot of variables that come into play with that zero voltage point, so many that it would be virtually impossible to maintain it. These factors are the actual channel you are transmitting on, the type of coax used (RG 58 or RG 8x), the quality of the coax, etc. In most cases this zero voltage point will be achieved around 12' if using average quality RG58, but once again this will vary due to more of the above mentioned variables. This zero voltage point is such a moving target and so insignificant when compared to other components of the system that it should not be considered to be top of list of priorities, or even close to the top. Use the amount of coax it takes to reach from your radio to your antenna base. Concentrate more on grounding, antenna location, and tuning your antenna length for SWR. There is a level of loss when dealing with connectors in coax which is usually around .5 db per connection. In my opinion that is a fair trade off for not having to tear your roof apart to run new cable. I would splice it using two UHF connectors and use another piece of matching coax of RG58 or RG8x, whatever is there now. Make sure you have a quality antenna, good grounds, good ground plane for the antenna, and your antenna is adjusted for SWR. In the end it is your stuff and your choice to believe what you want from the internet or books. I am no expert in radio or CB systems, but I was a radio tech in the Army and a senior field technician for Motorola for 5 years if you are wondering where I came up with all of this ****. [/QUOTE]
Insert quotes…
Verification
Post reply
Latest posts
B
For Sale
Artec Back-bone truss for 14 bolt
Latest: Bebop
Yesterday at 7:19 PM
Off Road 4x4 Parts For Sale
P
YouTube of the day
Latest: paradisepwoffrd
Monday at 8:21 AM
General Discussion
Cash LeCroy Illness
Latest: ridered3
Sunday at 2:58 PM
General Discussion
For Sale
Jeep TJ tube buggy for sale $32,000.00
Latest: ridered3
Saturday at 3:52 PM
Vehicles For Sale
Official "Post your trail riding pics" Thread
Latest: Piros 1
Saturday at 2:27 PM
General Discussion
Forums
Rock Crawling Forums
Tech & Fab
CB Antennea Cable Splice?
Top