I'm just putting this out there, I don't want to get rid of it and I don't have to but I was just wanting to see my options.
This rig is built very well and it works very well. It does have a good bit of body damage but it's mainly on the hood. The only difference in it from the pics is that I put the windsheild on and put a new set of Corbeau JP seats in it. Here's the breakdown on it.
CLEAR ***LE
1994 Jeep Wrangler
116" WB
350 V8 with a mild cam and aluminum intake
Holley Projection
TH350 Trans with shift enhancements
NP205 T-Case with 32 spline output shaft
Wide Open Designs Clocking Ring
1350 Joints/yokes
New Joints in the axle shafts
Flat Belly Skid
B&M Shifter
D60 Front
35 Spline Shafts in & out
6.17 Gears
Detroit Locker
Warn Drive Flanges
New Hub Bearings, Seals, and Brakes
HD D70 Rear
35 Spline Shafts
6.17 Gears
Welded
Disc Brakes
4 Linked F&R
Coilovers Front
Coil Springs Rear
PSC Double Ended Ram Hydro Steer
PSC Pump
PSC Resivour
Full Cage Tied To Frame
Corbeau JP Seats (1 Ride)
4 Point Harnesses
Factory Rear Seat
Uniden CB
Tach, Water Temp, Oil Pressure, and Volt Gauges
Warn 8274-50 with a NEW motor and NEW Solenoids
In Cab Winch Control
RCI Fuel Cell
42" TSL's with 50% +/- Tread
Allied Rock A Thon Beadlocks with Coleworx Rings
On Board Air (engine mounted compressor)
This rig works well and is ready to ride today. If you have any questions, feel free to ask.
TRADES, THE ONLY TRADES I'LL CONSIDER IS FOR A CAMPER. It can either be a 5th wheel of bumper pull. NO FEMA TRAILERS. I don't want a peice if junk either. If you've got one let me know.
The Price is $10,000
1-662-321-0758
[email protected]
Location: Pontotoc, MS (North Ms)
This rig is built very well and it works very well. It does have a good bit of body damage but it's mainly on the hood. The only difference in it from the pics is that I put the windsheild on and put a new set of Corbeau JP seats in it. Here's the breakdown on it.
CLEAR ***LE
1994 Jeep Wrangler
116" WB
350 V8 with a mild cam and aluminum intake
Holley Projection
TH350 Trans with shift enhancements
NP205 T-Case with 32 spline output shaft
Wide Open Designs Clocking Ring
1350 Joints/yokes
New Joints in the axle shafts
Flat Belly Skid
B&M Shifter
D60 Front
35 Spline Shafts in & out
6.17 Gears
Detroit Locker
Warn Drive Flanges
New Hub Bearings, Seals, and Brakes
HD D70 Rear
35 Spline Shafts
6.17 Gears
Welded
Disc Brakes
4 Linked F&R
Coilovers Front
Coil Springs Rear
PSC Double Ended Ram Hydro Steer
PSC Pump
PSC Resivour
Full Cage Tied To Frame
Corbeau JP Seats (1 Ride)
4 Point Harnesses
Factory Rear Seat
Uniden CB
Tach, Water Temp, Oil Pressure, and Volt Gauges
Warn 8274-50 with a NEW motor and NEW Solenoids
In Cab Winch Control
RCI Fuel Cell
42" TSL's with 50% +/- Tread
Allied Rock A Thon Beadlocks with Coleworx Rings
On Board Air (engine mounted compressor)
This rig works well and is ready to ride today. If you have any questions, feel free to ask.
TRADES, THE ONLY TRADES I'LL CONSIDER IS FOR A CAMPER. It can either be a 5th wheel of bumper pull. NO FEMA TRAILERS. I don't want a peice if junk either. If you've got one let me know.
The Price is $10,000
1-662-321-0758
[email protected]
Location: Pontotoc, MS (North Ms)
what u gonna replace it with Brian??
