whiskeymakin
Well-Known Member
I started this build a year ago with intentions of keeping it around. Well, we decided to start the process to adopt a child about 2 months ago and as some of you know its not cheap. We are very close to having cases presented to us. The reality of ever getting out in the woods in the near future is slim to none.
anyways, here we go....
I designed the chassis in bend-tech and built it all myself its all 1.75x.120 hrew I'm about 6'3" 215 and its pretty comfy. Weighs around 2900 without anyone in it
20" belly, 113" wheelbase, overall height is around 74"
2001 Honda 3.0 v6 I just put a new timing belt kit and water pump on it. cant remember the mileage....around 180xxx I think, runs like a Honda should!
Tim beatle harness and computer
transmission (Honda) is fresh built and the carrier/spiders are welded to send power to the transfer case from one output.
Nissan Datsun divorced case (low miles)
1310 yoke flanges
1310 balanced drive shafts, 2" dom
Full PSC kit brand new (tim beatle power steering bracket) tc pump
PRP seats with mud drain, PRP harnesses
ARB air compressor with tire inflation kit
d44 axles from a waggoneer built about as good as you can get.
-front has a ARB, 4.88 gear, RCV 300m axles DOM tie rod with 3/4 heims
-rear has a Detroit, 4.88, Dutchman axles, sleeved with some thick DOM tube
Currie Anti rock sway bar on the rear
7/8" ruffstuff heims, 2"x.25 DOM lower bars, 1.75" uppers
Ruffstuff 3/8" thick link tabs
New Fox shocks, front has 14x2.0, rear is 16x2.0
limit straps on all 4 corners
M/T Champion beadlocks 15x10 with 38.5 tsls hold air great, one leaks down over about 4 days
ar400 skid plate (1/4")
1/2" hdpe boat side skids
Led lights
panels are .060 and .080 aluminum
Jazz 12 gallon fuel cell, walbro 255 pump, Russel filter, mostly -an6 fittings
Kicker wakeboard speakers, Bluetooth pyle amp
Torque b.t. obd2 scanner to give you the gauge readouts to your smart device
Room on the back for a cooler and tool box
$18,000 or may trade for something with 4 seats
Located in Tullahoma, tn
931-581-4two94
anyways, here we go....
I designed the chassis in bend-tech and built it all myself its all 1.75x.120 hrew I'm about 6'3" 215 and its pretty comfy. Weighs around 2900 without anyone in it
20" belly, 113" wheelbase, overall height is around 74"
2001 Honda 3.0 v6 I just put a new timing belt kit and water pump on it. cant remember the mileage....around 180xxx I think, runs like a Honda should!
Tim beatle harness and computer
transmission (Honda) is fresh built and the carrier/spiders are welded to send power to the transfer case from one output.
Nissan Datsun divorced case (low miles)
1310 yoke flanges
1310 balanced drive shafts, 2" dom
Full PSC kit brand new (tim beatle power steering bracket) tc pump
PRP seats with mud drain, PRP harnesses
ARB air compressor with tire inflation kit
d44 axles from a waggoneer built about as good as you can get.
-front has a ARB, 4.88 gear, RCV 300m axles DOM tie rod with 3/4 heims
-rear has a Detroit, 4.88, Dutchman axles, sleeved with some thick DOM tube
Currie Anti rock sway bar on the rear
7/8" ruffstuff heims, 2"x.25 DOM lower bars, 1.75" uppers
Ruffstuff 3/8" thick link tabs
New Fox shocks, front has 14x2.0, rear is 16x2.0
limit straps on all 4 corners
M/T Champion beadlocks 15x10 with 38.5 tsls hold air great, one leaks down over about 4 days
ar400 skid plate (1/4")
1/2" hdpe boat side skids
Led lights
panels are .060 and .080 aluminum
Jazz 12 gallon fuel cell, walbro 255 pump, Russel filter, mostly -an6 fittings
Kicker wakeboard speakers, Bluetooth pyle amp
Torque b.t. obd2 scanner to give you the gauge readouts to your smart device
Room on the back for a cooler and tool box
$18,000 or may trade for something with 4 seats
Located in Tullahoma, tn
931-581-4two94