I've kinda lost interest in building a buggy for myself, so I've got a lot of stuff laying around collecting dust. I figure someone might be able to get some use out of some of it.
350 SBC - As it sits now it is a long block with valve covers, oil pan, timing cover & water pump. Fresh motor, never been run,started life as a Vortec motor.
.030 over 10.5:1 Hypereutectic flat tops
GM Performance Parts "PM" rods
Patriot Performance Aluminium heads,Combustion Chamber: 64cc ,Intake Runner: 185cc ,Exhaust Runner: 62cc, Stainless under cut 2.02/1.60 valves, Comp springs & retainers.
Comp roller cam .268/.276 advertised duration .495/.502 lift
Comp Pushrods
1.5 Roller rockers
Aluminum Flow Cooler water pump.
Will also include used Edelbrock Pro Flow Fuel Injection part #3500 with MSD 6A box $1800
TH400
4WD K case, Fresh rebuild with HD clutches & steels zero miles since rebuild -$350
STaK 3 Speed Monster Box
4.33:1, 2.43:1, and 1:1
Passenger side drop
32 spline input (TH400)
1350 yokes front & rear
TH 400 adapter
-$2200
Dana 60 front & rear housings
Front is GM passenger side drop, Trussed & set up with brackets for 4 link, cross drilled rotors, new calipers. Does not have gears, carrier, shafts or lockouts/drive flanges but complete otherwise.
Rear is a 60 HD, bored out for 35 spline shafts, completely trussed & set up for 4 link, disc brake brackets & cross drilled rotors. Does not have gears, carrier, axle shafts or calipers.
-$600 for the pair
5.38 D60 ring & pinions
2 sets of Yukon gear 5.38 Dana 60 standard rotation, Cryo treated. They have been installed but never ran
-$275 for both sets
D60 Detroit Locker
P/N 225S-29A 35 spline, 4.56 & up, installed into housing to set up gears but never ran
-$475
MSD Pro Billet distributor
P/N 8360 Pro-Billet Ready-to-Run, Magnetic Pickup, Vacuum Advance, Chevy Big/ Small Block with bronze gear. less than 500 miles total run time on it.
-$100
Winch rope
50 ft of Amsteel Grey 5/16 rope with abrasion guard & aluminum fairlead for short drum winch.
- $125
Chromoly Heims
16 - 1" X 1" Rod End Supply cromo heims ( 8 LH & 8 RH), with weld in bungs & stainless high misalignment spacers that reduce the bolt size down to 3/4" - $650
Will consider resonable offers. All items are located in Gallatin TN
350 SBC - As it sits now it is a long block with valve covers, oil pan, timing cover & water pump. Fresh motor, never been run,started life as a Vortec motor.
.030 over 10.5:1 Hypereutectic flat tops
GM Performance Parts "PM" rods
Patriot Performance Aluminium heads,Combustion Chamber: 64cc ,Intake Runner: 185cc ,Exhaust Runner: 62cc, Stainless under cut 2.02/1.60 valves, Comp springs & retainers.
Comp roller cam .268/.276 advertised duration .495/.502 lift
Comp Pushrods
1.5 Roller rockers
Aluminum Flow Cooler water pump.
Will also include used Edelbrock Pro Flow Fuel Injection part #3500 with MSD 6A box $1800
TH400
4WD K case, Fresh rebuild with HD clutches & steels zero miles since rebuild -$350
STaK 3 Speed Monster Box
4.33:1, 2.43:1, and 1:1
Passenger side drop
32 spline input (TH400)
1350 yokes front & rear
TH 400 adapter
-$2200
Dana 60 front & rear housings
Front is GM passenger side drop, Trussed & set up with brackets for 4 link, cross drilled rotors, new calipers. Does not have gears, carrier, shafts or lockouts/drive flanges but complete otherwise.
Rear is a 60 HD, bored out for 35 spline shafts, completely trussed & set up for 4 link, disc brake brackets & cross drilled rotors. Does not have gears, carrier, axle shafts or calipers.
-$600 for the pair
5.38 D60 ring & pinions
2 sets of Yukon gear 5.38 Dana 60 standard rotation, Cryo treated. They have been installed but never ran
-$275 for both sets
D60 Detroit Locker
P/N 225S-29A 35 spline, 4.56 & up, installed into housing to set up gears but never ran
-$475
MSD Pro Billet distributor
P/N 8360 Pro-Billet Ready-to-Run, Magnetic Pickup, Vacuum Advance, Chevy Big/ Small Block with bronze gear. less than 500 miles total run time on it.
-$100
Winch rope
50 ft of Amsteel Grey 5/16 rope with abrasion guard & aluminum fairlead for short drum winch.
- $125
Chromoly Heims
16 - 1" X 1" Rod End Supply cromo heims ( 8 LH & 8 RH), with weld in bungs & stainless high misalignment spacers that reduce the bolt size down to 3/4" - $650
Will consider resonable offers. All items are located in Gallatin TN
