Peterbilt flatbed

Hardline Crawlers - Rock Bouncer Builds, Tech & Off-Road Trail Talk

Help Support Hardline Crawlers:

Yeah a little bit, it wasn't to bad loading up. I figured I could always find a low spot to unloa/load
Can you dump the air bags? Or is that pic with it dumped? Dumping the air would definitely help
 
how are you planning to strap it down? going to the center? short straps to the ends of the deck? tire straps?
I used short straps, going to end of the deck. I may try strapping to the center. I have 8, recessed tie down points
 
Got one toolbox mounted, was going to put one on the other side, but one of my dogs cost me about $700. So I will get it after RBD then skirt it. Built a rack for the camper too.
PXL_20211121_211544445.jpg
PXL_20211121_211615079.jpg
 
As an Amazon Associate we earn from qualifying purchases. Product prices and availability are accurate as of the date/time indicated and are subject to change.
I’d hang a cheap set of heavy duty mud flaps behind your boxes. If not the rock chips will start and you know what will follow that. Looks great btw. I’d drive that sucker to the grocery store :driving::dblthumb:
 
Well how was the trip in the big rig?

What was your overall mpg?

Also, what would you like to change on this setup?
 
Well how was the trip in the big rig?

What was your overall mpg?

Also, what would you like to change on this setup?
It was good, rode as good as my f250, best I can figure about 8-9 mpg. Which is the same as the Ford, but I'm pulling a lot more weight. Once I get the tune cleaned up I think it will do a little better. Nothing I would change as of now, I will be glad to get the fuel cell built on it, so I don't have to mess with figuring out where to put my fuel jugs.
 
It was good, rode as good as my f250, best I can figure about 8-9 mpg. Which is the same as the Ford, but I'm pulling a lot more weight. Once I get the tune cleaned up I think it will do a little better. Nothing I would change as of now, I will be glad to get the fuel cell built on it, so I don't have to mess with figuring out where to put my fuel jugs.
Good deal all around. I’m surprised your F250 got that bad of mileage with your old enclosed trailer. We get right at 13 for the Hawk Pride trip grossing right at 23k.

Any idea what your loaded setup weighs now?
 
Good deal all around. I’m surprised your F250 got that bad of mileage with your old enclosed trailer. We get right at 13 for the Hawk Pride trip grossing right at 23k.

Any idea what your loaded setup weighs now?
Truck is around 16k, I think camper is 7k ish, buggy probably around 4800, then Tool, generator, etc.. My Ford got 8.4mpg last time I pulled the enclosed and it still had factory tires, I can't imagine what it would have got after I put bigger tires
 
Truck is around 16k, I think camper is 7k ish, buggy probably around 4800, then Tool, generator, etc.. My Ford got 8.4mpg last time I pulled the enclosed and it still had factory tires, I can't imagine what it would have got after I put bigger tires
My alumiduty sucks pretty bad on mileage, especially towing. it isn't deleted
 
Truck is around 16k, I think camper is 7k ish, buggy probably around 4800, then Tool, generator, etc.. My Ford got 8.4mpg last time I pulled the enclosed and it still had factory tires, I can't imagine what it would have got after I put bigger tires

My alumiduty sucks pretty bad on mileage, especially towing. it isn't deleted
Forgot about y’all’s trucks being stock so that explains the differences in mpg.
 
BOSS Audio Systems BCPA10 - Single Din Chassis with Detachable 10.1 Inch Capacitive Touchscreen, Apple CarPlay, Android Auto, Bluetooth, No DVD, RGB Illumination, High Resolution FLAC Audio Amazon product ASIN B08V36PHDL

Looks like a nice head unit. I like that it swivels and looks like a pretty clear camera view too.
 
BOSS Audio Systems BCPA10 - Single Din Chassis with Detachable 10.1 Inch Capacitive Touchscreen, Apple CarPlay, Android Auto, Bluetooth, No DVD, RGB Illumination, High Resolution FLAC Audio Amazon product ASIN B08V36PHDL
I like the unit, just dont know if i would like the no dvd part. Unless you can watch them from a USB or Scandisk.
 
Going to cut out some half round steps on either side of the toolbox, and make a fender flare out of flat bar
 
Back
Top