Built 4.3L and NP435
Engine - New Price $1500
Chevy 4.3 V6
Bored .030 with 10.5:1 pistons
Stock rods and crank polished
Double roller timing chain
Comp Cam 270HR
Edelbrock valve springs, push rods, retainers, locks, push rod guide plates
Screw in rocker studs
Comp stainless roller rockers
Stainless steel undercut 2.02/1.60 valves
Mild port work done to heads
Edlebrock TBI performer intake manifold
Sanderson headers w/3" Magnaflow exhaust
Custom tuned chip in ECM
Full MSD ignition system with 6A box, MSD coil, MSD plug wires, etc…
Brand new aftermarket wiring harness
Custom off-road oil pan with ¼" bottom and 1/8" side plate
York A/C compressor (for on-board air)
200 amp alternator
PSC power steering pump
Flywheel
Mini starter
"You are getting the wiring and computer too, so EVERYTHING you need for your swap, except for radiator. If you built this engine and added all the little things I'm including, you'd have about $6000 in it".
Transmission - New Price $400
NP435 with Novak Dana 18/20 adapter (has adapter ring so it can work with small or large bore t-cases). There is an ear added to the case to work with GM bell housing as well as the "undrilled" ear was drilled out so you get all 4 bolts in the bell housing. Includes the bell housing, clutch, throw-out bearing, clutch arm, slave cylinder with mount and a Wilwood master cylinder with braided stainless line and hardware.
Please contact Roy @ (985) 778-3516
Location: Mandeville, LA
/Videos of it running/driving:
https://www.youtube.com/watch?v=HfQXKbFqZ-U
https://www.youtube.com/watch?v=NQ0gvOeyHQM
Engine - New Price $1500
Chevy 4.3 V6
Bored .030 with 10.5:1 pistons
Stock rods and crank polished
Double roller timing chain
Comp Cam 270HR
Edelbrock valve springs, push rods, retainers, locks, push rod guide plates
Screw in rocker studs
Comp stainless roller rockers
Stainless steel undercut 2.02/1.60 valves
Mild port work done to heads
Edlebrock TBI performer intake manifold
Sanderson headers w/3" Magnaflow exhaust
Custom tuned chip in ECM
Full MSD ignition system with 6A box, MSD coil, MSD plug wires, etc…
Brand new aftermarket wiring harness
Custom off-road oil pan with ¼" bottom and 1/8" side plate
York A/C compressor (for on-board air)
200 amp alternator
PSC power steering pump
Flywheel
Mini starter
"You are getting the wiring and computer too, so EVERYTHING you need for your swap, except for radiator. If you built this engine and added all the little things I'm including, you'd have about $6000 in it".
Transmission - New Price $400
NP435 with Novak Dana 18/20 adapter (has adapter ring so it can work with small or large bore t-cases). There is an ear added to the case to work with GM bell housing as well as the "undrilled" ear was drilled out so you get all 4 bolts in the bell housing. Includes the bell housing, clutch, throw-out bearing, clutch arm, slave cylinder with mount and a Wilwood master cylinder with braided stainless line and hardware.
Please contact Roy @ (985) 778-3516
Location: Mandeville, LA
/Videos of it running/driving:
https://www.youtube.com/watch?v=HfQXKbFqZ-U
https://www.youtube.com/watch?v=NQ0gvOeyHQM