WOD Hill Killer Chassis Build

nealcj8 · Jul 30, 2018

That buggy looks awsome. Great job!

!

wizzo said:
Actually, it wasn't a huge deal. Got it sorted out yesterday evening. We thought we were fighting a pump issue but turns out the bushings in the WOD steering column kit were just a little too tight on the steering shaft. We pulled the shaft and turned it down slightly and now it's great!

I had the same problem with my column.

June dog · Aug 6, 2018

Was this the buggy at somernights cruise?

wizzo · Aug 7, 2018

June dog said:
Was this the buggy at somernights cruise?

Yes, Terry took it up there.

June dog · Aug 7, 2018

wizzo said:
Yes, Terry took it up there.

Cool. Seen some pics of it on book of faces. Good looking buggy

Pineygroveoffroad · Aug 9, 2018

June dog said:
Cool. Seen some pics of it on book of faces. Good looking buggy

Billy, Mark and Darrell rode Sand Springs saturday with this buggy and a few others from around Glasgow. They said they all had a good ride and this buggy went as good as it looked!

wizzo · Aug 9, 2018

Wish I could have made it out with yall. Next time.

Dirt700 · Aug 15, 2018

That rig turned out super nice. Good work

cdemart2 · Aug 15, 2018

wizzo said:
Little update

Also wrapped up wiring. Fuse panels for accessories and engine.

I'll have some more over all pics today or tomorrow.

Build looks awesome. Where did you get those relays and sockets from?

smbroady82 · Sep 24, 2018

where does the cooler go and where are the cup holders???

ridered3 · Sep 25, 2018

smbroady82 said:
where does the cooler go and where are the cup holders???

I got to see this rig at AOP over Labor Day and did not notice/look for a cooler or cup holders so I am not sure.

However I was impressed by the level of detail in the finish work and even more impressed by how quiet it was.

wizzo · Sep 25, 2018

cdemart2 said:
Build looks awesome. Where did you get those relays and sockets from?

They are "hella" brand. Very nice stuff.

smbroady82 said:
where does the cooler go and where are the cup holders???

The tool box has been used as a cooler at least once so far. We talked about adding tie down to the tool box to allow a soft side cooler to be strapped to it. Cup holders are for full body jeeps, toyota's, etc. LOL

ridered3 said:
However I was impressed by the level of detail in the finish work and even more impressed by how quiet it was.

Thanks! It has a stock 5.3 for now. It may get a little more under the hood at some point but Terry was ready to get this buggy in the woods, not build a motor. Pretty sure it has a magnaflow? muffler. It isn't obnoxious to be around, which is nice. But you call on it and it has a good sound.

ridered3 · Sep 25, 2018

wizzo said:
Thanks! It has a stock 5.3 for now. It may get a little more under the hood at some point but Terry was ready to get this buggy in the woods, not build a motor. Pretty sure it has a magnaflow? muffler. It isn't obnoxious to be around, which is nice. But you call on it and it has a good sound.

Yeah I talked to him for 2 minutes at the top of Trail 22 (our group was parked due to Mattman's broken BroncoII) and mentioned I had been following the build on Hardline and was impressed by the quality of the buggy. Our discussion was while the motor was running and there was no yelling back and forth like it would with open headers or the buggy turned off.

Hotrod23 · Sep 25, 2018

drool

smbroady82 · Dec 30, 2018

I just noticed the grab handle.. nice touch sir... been studying this one trying to figure out where you’re gonna put my cup holders .. :smoke:

Sent from my iPhone using Tapatalk

showtime33 · Dec 30, 2018

Nice, Clean, a rig you can see out of for the win!

wizzo · Dec 31, 2018

smbroady82 said:
I just noticed the grab handle.. nice touch sir... been studying this one trying to figure out where you’re gonna put my cup holders .. :smoke:

Sent from my iPhone using Tapatalk

If the dash was different, we could have put switches up there and cup holders between the seats. My concern was reaching the switches while strapped in.

showtime33 said:
Nice, Clean, a rig you can see out of for the win!

Thanks!

smbroady82 · Dec 31, 2018

wizzo said:
If the dash was different, we could have put switches up there and cup holders between the seats. My concern was reaching the switches while strapped in.

I have some ideas ;D