Let's see some jeep rock bouncers!

Post up your jeep build and some specs!
I'll start with this tube chassis jeep we built in about 2003
Lt1 383 striker motor, four speed, narrowed Dana 60's, 12 in coil overs, 44 boggers, 112 inch wheel base and 26 inches of belly clearance

I just got my 46 willys "Dirty Bastard" Trouncer (trail ride / bouncer) Rockwell buggy on the trail.

My tube chassis
6.0 slight tweek
Twin steer rocks
Th400
Doublers
And some other stuff

Can't post photos as I don't have a photobucket account.

here mine

Skidkid said:

I just got my 46 willys "Dirty Bastard" Trouncer (trail ride / bouncer) Rockwell buggy on the trail.

My tube chassis
6.0 slight tweek
Twin steer rocks
Th400
Doublers
And some other stuff

Can't post photos as I don't have a photobucket account.

Click to expand...

Just checked out your build and that rig came out looking great. I can only hope my next rig is half that nice.


.

Monstercrawler said:

Just checked out your build and that rig came out looking great. I can only hope my next rig is half that nice.


.

Click to expand...

Thanks. I never updated my build thread over there. One day I guess I should.

Took it to SMORR this past rainy weekend and had a blast with it. Waiting on my new Stazwerks wheels as I'm done using innerairlocks. Pita to air up n down with them.

monster said:

here mine

Click to expand...

CSC build your chassis?

Nice buggy!

B.DRAKE said:

CSC build your chassis?

Nice buggy!

Click to expand...

I'd be afraid to get it muddy. 8)

Musta started out as a mail delivery jeep with pass driver.

sum bitch is huge.... but i like it

No bouncer, but lots-O-tube where a Jeep Cherokee used to be.
Still rocking the 4.0.
60/10.25
114" wheelbase

This what your lookin for?

Re: Re: Let's see some jeep rock bouncers!

Here's one I've been working on for a customer....

Technician said:

This what your lookin for?

Click to expand...

Hey technician I would like to see some more pictures if you have them.

B.DRAKE said:

CSC build your chassis?

Nice buggy!

Click to expand...

yes csc fab
thanks

Older pic, started as a rolled cj7, now has just enough frame to legally title it, 14 bolt front and rear, ford running gear

Here's my junk......

gsell said:

Here's my junk......

Click to expand...

How'd you run your No2, with your propane setup?

Here's mine


Sent from my iPhone using Tapatalk

throttlejunkie said:

How'd you run your No2, with your propane setup?

Click to expand...

I have always ran a bit of juice for those long hill climbs or side by side drags on saturday nights in the dirt with my big block buddies. (I run a 360 amc bock that I have tweaked a bit) When I went to propane I talked to Carey at gotpropane.com and I told him I wanted to run the juice with the propane. He told me he ran a car/buggy with a kit of his and just added a power adder, ( the little race gas fuel tank you see) along with the NOS. I run a small edlebrock performer plate kit ) under the propane mixer (aka carb in the gas world) kit that has beeen drilled out just a bit (probably 150hp) on top of the propane. I have a micro switch on the gas (propane) pedal that engages the plate system at nearly wide open throttle. So when I arm the nitrous, which turns on an electric fuel pump for the gasoline and the nos to the plate setup along with the regular propane input via the mixer. It works like a charm I have been running it for a few years. I have a list of obstacles I can give you not to run the juice on. It will eat front axles and drive shafts. I think I have it dialed in pretty good now with the stickies after retubing the driveshafts with some good 1/4 inch tubes, mainly the rear shaft. It is alot of fun to pull up to a hill and purge the juice out the hood and take off...... Sorry if I over explained it, but I always get questions about it, just want to be clear. PM me with any questions, I am no expert, but it is alot of fun .....