TBItoy
Well-Known Member
87 4Runner that I bought bone stock in 06 and built up since then.
Sold it to my buddy Gabe a few years ago, he tubed the front end last year.
Damage was done at the HL ride at GMP
BAD
Engine is blown, huge holes in both sides of the block, but it still drove out of the woods and onto/off the trailer.
GOOD
Built to hell front axle, 4.10
High Pinion diff with v6 carrier/locker
OG 30 spline Longs (RCVs)
Huge top and bottom knuckle steering arms tied together
ALL ARP studs
TG trunnion bearing eliminators
TG drive flanges
TG 8" DE ram
TG 1650 PS pump
Rear axle
V6 with Aussie 4.10
1/4 wall drive shafts
TCASES
Marlin Crawler R10 double case (10 degree rotated) flat belly
Long (RCV) rear output shaft
23 spline 4.7 rear case
Corbeau ultra front seats
Corbeau bench
4 harnesses
All cage is DOM, front clip is hrew
3 link panhard front
4 link rear
Jeep ZJ coils front
TJ front coils rear
Generic white shocks
38.5 Aetna cut SX
One has a big hole in the sidewall where it was previously vulcanized
15x8 2" backspaced W/ rim stiffeners
INNER AIRLOCKS
It's really a "firewall buggy",
No stock floor, seats are mounted like a "real buggy" on tube framework with tabs, loop over driveshaft, etc
No stock front sheet metal, radiator/lights/etc are all on tubework
WINCH
Tmax 9500 with synthetic rope
Cooler rack between rear seat and gas tank, large ammo can tool boxes(also keeps the kiddos legs in)
Drop a motor in and fix the tire and you are ready to ride.
$3000
Call/text Gabe 931-239-7903
Grimsley, TN
Sold it to my buddy Gabe a few years ago, he tubed the front end last year.
Damage was done at the HL ride at GMP
BAD
Engine is blown, huge holes in both sides of the block, but it still drove out of the woods and onto/off the trailer.
GOOD
Built to hell front axle, 4.10
High Pinion diff with v6 carrier/locker
OG 30 spline Longs (RCVs)
Huge top and bottom knuckle steering arms tied together
ALL ARP studs
TG trunnion bearing eliminators
TG drive flanges
TG 8" DE ram
TG 1650 PS pump
Rear axle
V6 with Aussie 4.10
1/4 wall drive shafts
TCASES
Marlin Crawler R10 double case (10 degree rotated) flat belly
Long (RCV) rear output shaft
23 spline 4.7 rear case
Corbeau ultra front seats
Corbeau bench
4 harnesses
All cage is DOM, front clip is hrew
3 link panhard front
4 link rear
Jeep ZJ coils front
TJ front coils rear
Generic white shocks
38.5 Aetna cut SX
One has a big hole in the sidewall where it was previously vulcanized
15x8 2" backspaced W/ rim stiffeners
INNER AIRLOCKS
It's really a "firewall buggy",
No stock floor, seats are mounted like a "real buggy" on tube framework with tabs, loop over driveshaft, etc
No stock front sheet metal, radiator/lights/etc are all on tubework
WINCH
Tmax 9500 with synthetic rope
Cooler rack between rear seat and gas tank, large ammo can tool boxes(also keeps the kiddos legs in)
Drop a motor in and fix the tire and you are ready to ride.
$3000
Call/text Gabe 931-239-7903
Grimsley, TN