Search results for query: *

Homemade cherry picker/engine hoist. Nothing wrong with it other than some mismatched hardware and surface rust. $40

Craftsman 10" bench top drill press and central forge 5" milling vise. Both have maybe 3 hours of use on them. I drilled two holes in the base of the drill press to mount the vise as it would not fit on the table. $100 for both. Milling vise...

Brand new in box 2005-2015 4wd tacoma leveling lift kit. (Spacers). Looking for $200. http://www.lowrangeoffroad.com/toyota-off-road-parts/2005-2015-toyota-tacoma-off-road-parts/suspension-lift-kits/lrt-2005-2016-3-1-leveling-lift-kit-for-toyota-tacoma-by-low-range-off-road-lr-lrtaco.html

I have a 8.8" rear axle out of a 88 mustang gt with a brand new set of 3.73 gears and a trac lok. As you can see it's just the housing with the gears and carrier installed. No axle shafts, brakes, or anything else. Comes as pictured. $200 SOLD Brand new pair of Moser 5 lug axles that are...

Yugo Npap Ak in 7.62x39 in great condition. I bought it new and have put a little over 400 rounds through it. Comes as pictured with 7 mags (5 polish surplus, 2 pmag), canvas sling, and 590 rounds of wolf military classic ammo (not pictured). $700 obo

Cmmg 16" wasp barrel, Anderson upper, carbine length handguards, white oak front sight, detachable a2 carry handle rear sight, a2 flash hider. Comes with a little over 250rds of reman ammo, no bcg or charge handle. $325 ASR Brake not included

Does anyone still cut and rotate Toyota front housings to get a better pinion angle? Or is a high pinion my only option? I'm not looking to go with duals any time soon.

Just picked up a 91' 4 runner with a 3.0 . I went to do emissions this morning and while trying to hold rpms I discovered a surge that starts around 1600rpm and goes away after 2600rpm or so. This only happens when revving with no load. Under load its fine. This is my first 3.0 so any tips on...

I'm trying to help a friend out with his 85' pickup with a 22re. It is extremely difficult to start when it's cold out. I'm talking like 30-40 minutes to get it to start. I've checked spark from the coil and from the distributer and both look strong. When i pull the plugs they are wet with fuel...

The winch is question is a M8000 thats about 4-5 years old now. I just bought my old truck back and the po thought that winch motor might need to be replaced. His reasoning being that it was spooling in extremely slow. I didnt think to ask him if it was only slow under load or not. The other day...

im posting this in hopes to give my dad some ideas what to check for since this is his car in question. Quick rundown: the car is a 63' vette that is a frame off resto. all brake components are brand new expect for the master cylinder which he rebuilt himself. the problem he's having is that...

Im planning on going up to walker on Saturday July 23rd and doing a little Birthday wheeling. Anyone else down to go that weekend?

i figure with the weather supposed to being pretty nice tomorrow that some of you will be out wheeling tomorrow. im planning on heading up tomorrow around 10-11ish. as of now im not going with any other rigs (everyone is either busy or their rigs are down) so maybe ill run into one of you up...

my sister boyfriend has a 98' ram1500 and one of the rear axle seals is leaking. i would like to help him out and replace the seal. my question is does the wheel bearing on these axle have to be pressed on/off to replace the seal?

i have a pace setter header with a 2.5" collector. i kept blowing he collector gaskets about every week, so i went with some heavier/thinker graphite gaskets. those last me about the same amount of time, so i decided to try some copper gaskets. anyone have good luck with copper? maybe im just a...

this is in the flange for my driveshaft on the front output on my tcase. the big gouges are from a little mishap last night. this is one of those tripple drilled flanges for toyotas. has anyone had problems with the slines in theres?

i have a vacume leak somewhere and i think i narrowed it down to the booster itself. i checked the online vacume line going to it and there were no leaks, so that lead me to believe its the booster itself. here's why: this only happens sometimes and when the truck is warmed up. i will come to a...

well i bought a 22re from a 93' pickup and am going to put it in my 87' this weekend. i havent found much, but from what ive read the harness is different at the injectors and your supposed to use an ecu from that year. anyways it seems like the easiest thing to do it just swap my intake from my...

so whats the difference in a short block 22re vs long block. is there specific years for a short block/ long block? i see engine remanufacturers list long/short block but ive never heard what block is specific to what years.

so i drove to my work to today to check a few things out on my truck. anyways when i start my truck and im about to leave there is white smoke puffing out of the exhaust and water dripping from the tip. so i figured the fawking head gasket let go or something. i pulled the oil cap off and sure...