Search results for query: *

1995 GT Mustang for sale. it has Factory stiffer suspension since it is a GT model. 205000 miles. I have installed numerous parts such as a fuel filler neck grommet, drivers side tie rod with an alignment. No engine or transmission... Perfect time to LS swap it! I was going to turn the car into...

have a 1993 4Runner that I am getting rid of. Has 253k miles on it. 3.0 V6 with the manual transmission. Runs good. Shifts good. Drives down the road. Within the last 3k mikes I have done the water pump, timing belt and new mud terrain tires. Needs a valve adjustment, brakes on the driver...

I have a ton of parts that I want to get rid of. Toyota Tacoma 3rz Gear Drive Adapter from AA, installed but not ran. 21 spline. $200 1979-1983 Toyota doors. Good shape, minor issues like a mirror missing. Has nice aluminum door panels. $125 1979-1982 Toyota truck round headlight conversion...

What's your guys opinion on either? When setting up gears, what do you prefer? And explain... Boonie and I were setting up my diff(he did most of the work:redneck: ) and we got to talking about what we think is better.

So im doing an EFI swap in my '80 1st gen longbed, Mark M says I can use a 2wd early 90's EFI gas tank and it will bolt up in the stock location, but thats if my truck is a shortbed. It is not. So wondering if a 2wd EFI gas tank out of a longbed truck would be the same as mine... My current tank...

So I'm about to flat belly my toyota. If I lift up the trans and case up to make it a flat belly, do I need to pay attention to the angle of tilt on the motor(front to back)? Anybody know what I'm talking about?

I have never understood why people leave there tow rigs running when they go to grocery stores and stuff like that. Sometimes leaving it running for hours or so. I know big trucks do, aside from running there generators for power and stuff. But aside from that I'm clueless. Care to explain?

I have a 3 wire GM alternator in my 80' toyota pickup, exciter wire is jumped correctly, and have been running this setup for about 4 months now no problem. So I was driving up the girlfriends gravel driveway bout a week or 2 ago, was in and out of the throttle goofing off and all the sudden...

Got my RE back from C&D machine and got all my rebuild parts. Now its time to put it all together, anybody got any tips on throwing it together?

How would a 6" wide rim act on 12.5" wide tire? Ballon? Blow beads? Tell me please!

I need the measurement for a 1st gen rear driveshaft fully compressed and about an inch left of spline extended. Thanks!

How much would one cost used? :corn:

So my truck is a 1980 with a '77 20R, it has a new FEN green alternator, 5 prong regulator. I put the new alternator in and plugged in the wiring in the back, started driving it around, noticed that the battery was getting overcharged. Got a volt meter on it and it was reaching 18 volts, so i...

Ive got a '80 toyota pickup and the brake booster is leaking, I also have the entire booster and master cylinder from a '95 4runner on my bench, could I use the '95 booster in my truck without modifications?

My older bro is finally putting his motor together and he got as far as putting the timing chain and the cam gear on. The only way he got it on is when he took the tensioner and the rounded guide off. The chain is now super tight and we cant get the guide and tensioner back on. Its an older 22r...

Who alls been up there? Went up there tonight and seen the washout. Its pretty knarly, but still passable...:eeek:

My bro is putting together his toyota 8" and his passenger side axle wont go in. It came out fine. Anybody else had this happen to them? The drivers side went in perfect... Also does it matter that the inner axle isn't 'connected' to the outer. (no c-clip)

I recently put a 22R in my toyota. My neighbor has a first gen toy that I used to have knowledge of where stuff went. I hooked up most everything except for a couple air hoses(ie couple of lines that go from the carb that the other truck didn't have). Also the truck has a stock toyota carb like...

Has anybody here ran a T-MAX winch. I like the looks of them (look like most others, anyway) and have heard a few good things about them. But they are new, and haven't had much press, I don't think. I know I will get the die hard loyaists of mainstay (Warn...) winch companies, which is fine. But...

I need to get some bumpers made up. Can you guys post up some pics of different designs of plate bumpers you made. Extra info, I have an early bronco. Cory,