Search results for query: *

Hey guys,any of y'all run that new trail down in oregon? Was currious if ya liked it and how long ya figure a group of 4 rigs could run through it.Is it a loop? any info y'all may have on the trail would be great! Thanks, Mike

Hey Guys Im sure and handfull or you guys on here have been to the Rubicon latley.I never have, but want to make a trip this summer.Just wandering what y'all would reccomend for the route to take and how long y'all think the drive will be. Sure appreciate any info you could give me on this...

What do you guys know about these struts? Im concidering selling my coilovers and going this route. It would be nice to chat with some folks that have had first hand experiance with them.:corn:

I was wondering if any of you guys know of a sealant type product that brake fluid doesnt ruin? The site window on my brake m/c on my chink quad leaks,and I was wanting to seal it up.

I tore into my dana 300 t case,I want to replace all the seals and front output bearings. I pretty much dont know what im doing,never had one apart.I removed those lil caps along side the shift rails expecting some springs and ball in there.I got nothing? are the springs and balls on the back...

I seem to think a 38'' tire would be ideal for my new rig im building.Its a sammy with 107" wheelbase should be a trail weight of about 3500lbs. I mostly wheel snatches and rimrock,I prefer trail wheelin but still enjoy the challenges of rockcrawling plus some dune thrashing. I can have a set...

This seems like a good spot for this thread its about the garage. Ive been doing alot of fab work latley and Ive always just opened the doors when it gets smokey in there,But now I have a/c and heat and i dont want to lose my cold/warm air.But as you know these fumes and such from welding and...

So does anyone know what a stripped ,stock housing weighs?

I need to make my toy front housing wider.I would prefer not to use alluminum spacers. Ive heard you can swap in some ifs parts and tacoma rotors and get 1.5" on each side. Is there a right up on this mod? anybody got some info or a link to the parts list of what i need to do this. Thanks...

What are you guys useing to convert the dana 300 output to a toyota driveline. basicly using the dana 300 t case and have toy 8" housings and I have toy drivelines I want to use. Any suggestions. I havnt found a conversion u-joint in precicsion brand,does spicer do the conversion joint? Or...

I was hoping somone could direct me where I could buy a toy v6 elocker new or used? Thanks Mike.

I took a much needed day off and went out to our secret spot and did some rock crawlin. Had a great day of wheelin and damn near destroyed my sj410 trying to fallow the big rigs through the canyon. Heres Jeatons "shitter" sportin 42"stickies and 114"wheelbase,4.3l. Orange crush's land...

Sorry for all the questions guys.But thats how you learn right... With youre help and lots of searching Ive decided on 2"x.250 wall dom for my bottom link material. Now I would like advice and opinions on the pan hard material and upper link material. Im thinkin panhard and upper link...

Im getting ready to buy some link material for my build.I was looking for some opinions on useing 2"x.250 wall square for my bottom links vs 2"x.250 dom round.Ive been quoted $4.45 per foot for square vs $11.70 per foot for the dom.Big saveings useing the square.Discuss please,thanks Mike.

Ive got my tuber up for sale,axial trans with dig.Custom billet parts everywhere.The rock rings are very trick.Sporting very new claws,cvd's in the front,new 55t novak motor.This rig is ready to comp,works very well. I keep the esc,rx,steering servo. you get all the rest for only $300.00 like...

Hey guys does anybody know what the I.D. measurement is on the yj springs eye? Thanks,Mike.

Next issue I would like to discuss.I would prefer to put the 4 link s&n style in the front of my rig also. Been doing some learning on this,it seems to me this could be a difficult adventure. Tell me if my thinking is correct please:with a 4 link front useing a steering box(scout) with ram...

Im a few months away from this choice on my build. The rig will be samurai based,toy axles,38" swampers,should weigh in around 3,200 lbs loaded with tools and parts. Whats youre guys opinion on the air shock vs the coilovers. My plan for the rig is trail riding and rockcrawling,I like to run...

Been a long time coming,I finally got back on my samurai buggy project.I spent all day out in the shop finallizing my transmission to t-case adapter.So I can work on getting the the motor/trans/t-case mounted in the frame. The specs: Samurai body tub(to be pinned in the front and dove tailed...

Hey fellow wheelin guys& gals,I own a auto parts store in Bentoncity,Wa.I have recentley been accepted as a Trail Gear distributor.Im stocking the long shock hoops and large diff armor for now.Soon I be stocking more stuff, youre suggestions on stocking items would be appreciated.Im thinking...