Search results for query: *

I am about due for a tranny in my 98' 12 valve. Fluid looks and smells SMOKED and I have a 100 fuel plate that isnt stock trans friendly. I have been looking at my options, and I have already decided on most parts of the build but I know some on this board have had it done. Need to decide on...

Hey all, I just bought a brand new 8.5'x24 enclosed trailer to haul my wheeler and other toys. The trailer has 3/4" plywood floors with 3/8" plywood walls. While the floors are nice and oil free I want to put some type of heavy duty oil resistant paint or coating down. I have been looking at...

Hey guys, figured I would pass on the word that another competition is coming up. Im not affliated with the promoter but I figured I would pass the word on. I have been told by a reliable source that this time the rock crawl course will be constructed with shotcrete, which should be...

I have been itching for a new project and I have been considering buying a wrecked Dodge and re-building it over the winter. Has anyone been through the state patrol inspection process? I will likely be buying the rig from Co-part, does anyone have any experience with them? Here are two that...

Does anyone have any information on this event? I have heard from several people that there is a rock crawl Sat the 7th, but nobody has a flyer or anything. Supposedly it will be a man made course?

I have Chevy front dana 60 wheel hubs that do not have the retaining ring groove machined after the internal splines, do I need to machine the groove to run my flanges? I have summit machine 35 spline flanges. Also, is the internal spring (like the one included with longfield drive flanges)...

What kind of high steer arms are you guys running with full hydro? I was thinking of using the basic style with the bolt on spicer cap. What about Ackerman or geometry? I have a double ended 10" ram (will be de-stroked) if it matters. What about the short tie-rods from the arms to the cylinder...

I am narrowing a chevy Dana 60 to toyota spring pad width. The toyota spring pins are 29.0" apart, and the chevy spring pads are 31.5" by my measurement. I want to use a dodge shortside axle (1.5" shorter) and a custom long side, 3.0" shorter. So 4.5" narrower total? Just making sure I am not...

Last weekend went snow wheelin and had a great time, until the end. Broke the low range gear in my rear case and the case itself. A tooth broke off and floated around for a while, then got sucked up into the gears and broke the case. Stock gears in both cases, 4.3, auto, 4:10 gears and 44 TSL's...

Ive checked online metals and a few other sources, but they want me to buy a 20ft stick ($$$). I am looking for 3.125" O.D. .188 or .250 wall tubing to retube a Dana 60. Any ideas?

What kind of luck are people having with the higher Dana 60 gear ratios? I was considering either 5.86 or 6.17, but I dont want to break ring and pinions. I have 35 spline yukons and drive flanges on order, I would prefer to keep the weak point the shafts or joints.

Last week, vacuum pump. This week, blown fuse. I cant wait for next week. Heck, I have put almost 3500 miles on my powerstroke since I bought it, I guess I am lucky so far:shaking: Does anyone know what causes the #22 30A maxifuse under the hood to blow? The owners manual says its the fuel...

My roommate and I are headed up to the rocks Saturday morning to play around, anybody going to be up there? If there is anybody from Ellensburg that wants to tag along we will be stopping at the Super 1 foods parking lot at 9:30 or so then unloading at Barber Springs Road. My roomate has a mild...

Does anyone know a part number for a paper air filter with a 3.5" inlet and flange for a hose clamp? Or somewhere where I can order one? I was using a K&N but it lets too much dirt in. I looked through all the boxes at shucks and napa but there werent any filters with a place for hose clamp. A...

I have been tinkering with my 96' Powerstroke and wondering what my next mod should be. So far I have done the DIY intake and turbo back exhaust, and I am in the process of installing a pyro and boost guage. I have ordered a chip also. The truck is a 5 speed and I am not worrying about the...

Would you do it the same way as before? I am bored and need a project. I am thinking its kind of silly to buy a sixty for 900 and not use the brakes, shafts, hubs, steering, gears, carrier, diff cover, or yoke. I have also been thinking about retubing a newer superduty axle as some of them come...

I am shopping for a new diesel tow rig and have a few questions. I have it narrowed down to 2 types of rigs, 94-97 powerstrokes and 94-98 12v Dodges. The Dodges seem to be $1500-2000 more for the same options, are they really worth the extra $? Is there a way to tell if the track bar is loose...

Went to Reiter for the second time and camped and wheeled, had an awesome time. I got a few pictures but alot were blurry. Saw alot of rigs I recognized from the board. We ran most of the trails, there were broke cherokees on almost every one :flipoff: My carnage: oil filter motor trans pan...

I have been thinking about buying a new towrig as I am getting really tired of towing with my F150. I am looking to spend about $6500 or less and the cleaner lower mileage cummins and powerstrokes are not really there. I am thinking of getting a 2wd but I use the 4wd on my truck alot and I am...

Dickwart and I made a run up to funnyrocks and moonrocks yesterday, it dumped snow the whole time. I had never been up there with that much snow before, it was kinda of fun rallying around where you usually can only just creep along. Here are the pics I got: Funnyrocks Brad and Berto by the...