Search results for query: *

Does anyone know of a good machine shop with decent prices in the Snohomish/Arlington area? if so let me know please. I think Newall in Arlington is a fair shop. I need to have an aluminum shift plate milled/bored out for a larger JB conversion output shaft bearing.

Ballistic Has anyone ran the Ballistic Fab joints? I almost went with them but I had good feedback on the Johny's so I went with them. The Ballistics are what I will get if these bend.

pics Sorry too high of res. I will get some up soon!!

Almost ready to wheel. Just getting done re-doing the front; 4 link, hydro and coilovers!! Wheelin' Reiter 21st!!

I second this set up,I also run a taurus fan,I run it with a HD40a relay and run the switched ground thru a 1985-1989 honda accord thermal switch,it screws right into a standard chevy(1990-2000ish) water neck and turns on auto at 185-195ish and works awsome!!I have this on a chev 350 engine in...

Spew You may want to check the crank case vent if it is not venting, it creates pressure that has to escape somehow.bad rings will also create blow by,you should be able to have the breather cap off when it runs,if it is blowing a lot of air out,you have either a cracked piston or bad...

So I thought I should put in a plug for Tera industries. I built my D300 this last summer and installed a Tera low 300 kit a guy up the road had on the shelf brand new in the box (3 gear set) and ordered the AA 32 spline output and a full rebuild kit for it. it turned out great! I ran it 3 times...

Money?mouth? ok SSSickboyeee!!! you need to step off the sidelines and get yourself a rig!! 21st century!! Ha!:fawkdancesmiley:

thanks! I will call them Mon and let you know what they say!

has anyone had issues with their tera low gears?? I bought a set from a guy who had a new set on the shelf for a long time and the set only had 3 gears in it;two small ones and the large center one with one piece with two gears on it. well I set it up to the book exactly with new bearings seals...

Tps I agree,I would check out the tps(throttle position sensor)it is mounted on your intake plenum on the opposite side from where your throttle hooks up and has 1 plug.:awesomework:

It is a kingpin dana 60. I like the bead idea,also when I took a look at the tie rod(factory 1 ton) it is actually bowed.I have high steer so it must have been stressed over at Naches this last weekend.so I am going to start with chromoly tie rod and the dynabeads,then I'll let you guys know how...

there is a check valve right where the manifold vacuum line hooks in, its plastic.if you run the truck and pull it out of the booster it should have a large suction sound.(after you turn the truck off)if not you may have a bad check valve or your vacuum line may have a pin hole in it.is the...

wobble the toe is a total of .25. I haven't tried the balancing and all the joints are tight last I checked,I will check again,I know after every trip things change. is dynamic balancing the same as patch balance where they laminate sheets of rubber to the inside of the tire?

So I need some help figuring out what camber and toe I need to run with my 42" tires,I had 38.5's on and it wasn't a problem. now with the 42's I get serious death wobble at about 35 mph. my current caster is +5 degrees and the toe is .25" and I have a rs5000 damper on. anyone have any specs on...

Screwed THAT'S WHAT I WOULD DO GO BUY $1,560.00 WORTH OF TIRES AND $400.00 OF CHEAP WHEELS AND $4.50 OF CRAPPY SHEET METAL SCREWS AND DO A 1950's QUALITY BEAD LOCK UPGRADE, OH YA BABY!!:looser:

Dana 300 What the last guy said is right! I just tore mine down and installed the tera 4-1 and AA 32 spline output. remove the large access panel and I think you shift into neutral and use a 8-10 inch extention with a allen to loosen the shift shaft set screws, remove the output yoke and shift...

Steel Skagit river steel in Mt. vernon/Burlington is the cheapest unless you go to whiteside in woodenville.

D60 tube seals. So where do you get these and how much are they?????