Search results for query: *

Help me with my math I want to figure out how many times the drive shaft needs to turn to go 30 miles an hour? here are the specs: 47" tire = (12.25' Circumference) 5.13 axle ratio 30(mph)x5,280(feet in a mile)=158,400 (feet per hour) 158,400/ 12.25'(tire circumference)= 12,930.61 tire...

My Douchebag friend asked me to post this question. He has replaced the starter, ignition switch, starter relays, neutral switch, and checked the fuses, and his XJ won't start. He is hoping for some other suggestions. And yes the battery is charged, and connected.

I have a friend who is looking for some leafs that would be about 72" long or somewhere around, from hoop to center pin would be about 36" If anyone knows of some let me know. Also if anyone has some they want to sell let me know.

Does the Dodge unit bearing for the AAM front axle come in a 35 spline version, or are they 30 spline? I still have this AAM front axle, that I am considering to install into my Ford, so I can steal the D60 to throw into my YJ. I am either considering throwing the unit bearings from the D60...

How much difference is there between the dana 60 carrier, and the dana 80 carrier? I am thinking about building a Dana 80 axle with a Dana 60, 40 spline spool. Or is there a spool for a Dana 80? Can it be machined to fit 40 spline axle shafts? The Dana 60, 40 spline shafts are 1.705", and the...

So in line with our current luck lately, we have yet another thing happen. So what does this mean? * ICP voltage not at expected level * Turbo boost pressure not detected This is a 1999 F350 7.3 PSD What do I need to do to fix the problem.

So I have a friend who is considering to buy 49" Iroks. How do these tires do? Are they better than the smaller size Iroks or still just the same? How do they compare to other tires such as, Tsl's, SX's, Boggers, Ltb's?

So is there any way it is possible to modify an AAM front axle to accept Dana 60 lockers(maybe a spool) and gears.

So can I assume that a 1983 F-250 diesel 4x4, and a 1986 F350 dually 4x4 would have D60 fronts? Or is it just a pipe dream?

SBC wiring questions I am stuck wiring my SBC. To start it off, it is a 1974 SBC, with a TBI setup off of a 198? Camaro with a 305(BTW the chip is already burned to work for what I have). The wiring harness is from Affordable fuel injection, which includes the bare minimum to make it run. This...

Are they gonna make a huge difference on a wheeler, or should I stick with Vacuum boost?

So I have my MJ suspended, now but I am assuming that the spring rate of the heavier springs is a little too much. When I place the weight of the Jeep on the springs, it only compresses about 1 inch. Which sets the top of my Jeep at about 8'6" which I think is a little too tall, and if I end up...

I am wondering if a Mercedes turbo diesel would be worth a crap for a wheeler engine. I really would prefer a diesel over a gasoline engine, so if this would be a good engine please let me know. Here is the one I am looking at: http://seattle.craigslist.org/kit/car/440436077.html

So approximately what is the O.S. frame width of a Chevy/GMC FS truck, Blazer, or Sub.

So I feel I have driven my Yj to a point where every time I take it out I break something. I think I am where I need to make a decision, finish one of my other rigs, and then start on the complete Yj rebuild, or drive the fawker right into the ground, then start the complete Yj rebuild.

Where do I go to get internal splines Machined?

I am tired of breaking D44 shafts. I know, I know, I need to upgrade to a D60. What are the absolute best shafts made for a D44.

I am only posting about it, cause we are going to go up Izzy off on the first two side trails, up to the TOD, back down, then over to BYS(this is why I posted a separate thread). All are invited, although I would prefer to not spend the day fixing someone else's rig. I know this is short notice...

We were up at Reiter at noon, and someone had dumped a 1986-1993 ranger windows are broken, and it was pretty trashed. If someone isn't able to pull it out I can head up to pull it out, just let me know. It is at the start of the Rock Garden.

I heard of someplace called "Moonrocks"(saw it on friends wheeling video), If it is a real place, I would like to plan a weekend trip around there soon. I prefer to wheel in a group, so if someone is interested, let me know.