Search results for query: *

Any body hunt there much is it hard too figure out where you can and can't hunt the map looks like it is pretty confusing ..

there any way you can test with a meter or possible a local shop south that test hei dist to see if there any good got a new motor and the guy thru a hei dist in but said he was not sure if it was good been sitting for a while would like to know before i put the motor in kinda a pain to pull...

talked to a buddy this week and he said he seen my missing hub laying in the middle of the 520 at evan any one by any chance pick it up?

OFF ROAD ANIMALS 18 Annual fun run at evans creek WA Aug 14 2010. All entries must be street legal with insurance. TRAIL PASSES ARE REQUIRED BY THE US FOREST SERVICE. Passes can be purchased in Burnett or Wilkeson on the way to Evans Creek. Lots of door prizes and Cash Prizes. After the run...

k got a 350 with toyota tranny what slave cylinder do i use? heard a land cruiser one works but could i use a stock toyota 5spd as well! will it bolt up

going to put the chevy master on a toyota dual diaph booster just wondering if you think the 1 5/16 might be too big if i should step down to the 1 3/16 bore..i just dont wanna have a stiff pedal

dont have good brakes really mushy and goes all the way to the floor i have a88 toyot with disk 44 front and 14 bolt disk rear and still running a stock master... is there a bolt on master that will help with braking or a boster and master i dont have to use tons of force just have to push them...

i got a bad ball joint on my tie rod end and are haveing a hard time find ing a new one with the right size tapper and threads.. so was kicking around the idea of drilling out the tapper on the knuckel side and running a heims joint (got the idea from a guy at shucks) any one do this up or down...

any one done a mallory tbi convertion or other brand on there carbed motor! look pretty easy just bolt up and plugs in has ecu distriubter fuel pump regluator and all the wiring and sensors and throddel body.. just wondering if it is as easy as looks or more or more of a pain!

i got a chevy dana 44 up front i took the hub off and counted 19 splines on the axle shaft it self... i need a new hub for it can i use ford d44 hubs and is the 19 spline relivent or is a hub a hub as long as i have the original hub.. and on that note any one have a good warn or compariable...

got a 350 in a toyota i just picked up has a holley and runs like poop floods out and back fires! what i wanna know is what carbs you guys running and what is the best one for off road use... and i know if i was rich i would just put fi or tbi on it but for now this is going to have to work!

got a 97 7.3l what is a good programer for around 500 buck.. i have the edge evolution it is cool adds alittle but seems to be messing with the truck hard start when it is cold (harder than normal) and i hate that i cant adjust on the fly.. what good is extreme power if you have to stop shut it...

have a 97 powerstroke if i dont let it warm up for at least 10-20 min it runns like **** and will shut off..it will blow smoke and huff and fart and die i can restart it right away but it will keep doing it unless i keep my foot barried in it for about 2-3 min...it was doing this and now i got a...

an body looked at the kits for doing air ride on mini trucks? looked at a few they seem like there alright and at about 250 bucks cheap they has all the joints and rods grade 8 bolts and nuts jam nuts and tabs you weld on any body tryed this ! seems pretty simple way of going about it...

has any one on here done a 3.4 in a 85- older truck heard of a few people doing the 3.0-3.4 liter and sounds like its a headach! but read somethign on pirates about the 3.4 uses the same bell housing and motor mounts... change the wiring and "sounds like almost a bolt in thing " am i wrong.. i...

i recently put duels in the toyota! i heard over the weekend that you can use a v6 short box ex cab rear drive line in place of my rear drive line and it will bolt right up with out cutting it! not sure if this is true or not i cut mine to fit but it has a small shimmy and would not mind haven...

i am going to build a flat bed for my toyota would like to see some of your guys see how they mount and look got a general idea of what i want just like to see of the other options! and maybe get a different idea

have a question on wagoneer 44s... how wide are they and would they bolt under a cj if the perches were moved at most? and are they good axles

Smittybilt XRC8 8000lb Electric Winch #97281 any one running this winch is it any good seems like a good deal for the price?

wanna get all the parts before i tear into it so...i got a 68 ford 302 motor in my jeep cj5 wit a t18 and d 20 on it. .. if i pull the 302 and go back to the 304 will the bell housing bolt upto the t18 tranny (the ford t18). or do i have to find a new one i have both the bell houseing off both...