Search results for query: *

I have the c0305 miss-fire no. 5 cylinder. Engine is pretty new long block with about 20k. Original manifold wires and ecu. I have replaced: cap, rotor, wires, plugs, and fuel inj spider. Spider showed signs of leakage, manif was real clean around no 5 injector. Compression is 150. The...

RD166 dana 60 LP air system is tight holds air overnight. Lines dont leak and are not plugged. when wheels are in the air it works perfect, passes ARB's bench test for in vehicle. appeas to engage and diss engage. disassembled it and no stripped splines on the axel and no broken axels. Get...

I have 5 bolt outers and want 8 bolt. Will the 8 bolt outers from a chevy ten bolt fit? I have access to one free

i have a 97 lexus aka 4runner.... the driver door slowly stopped working now it wont open the door at all. i took the panel and all rods and keepers are intact. i can see the mechanisim you need to push to unlatch the door. the outside handle moves it much farther than the inside latch.....i...

Will be near moab and i have my buggy with me. Id sure like to hookup with some locals or anyone to go wheeling. We will be there on the 16th of Feb. Anyone have any local contacts in the area?

I have a dual tank setup on my motor home and recently it has issues, vapor locking on a really hot day. it was in the 100's so it was pushing the limits and was towing 4500 ish pounds. So i want to help this problem by adding a small pusher electric fuel pump back by the tanks but not sure...

where can you buy them? i need 20ea, steel grade 5, 7/16 NC X1 1/2" long bolts pre drilled for lockwire. my full float rear axel's bolts keep working loose. the 7/16" dia is what is hard to find even mcmasters does not list them..... champion does not carry them or cannot order them?:wtf:

in my day of building my hotrod mustang the cool thing to get rid of points in the distributer was to replace them with a photo cell. :wtf:what is the current cool setup for an ol school car to remove the points? this is in a 70 mustang im trying to help the kid fix up his pony. we put in a...

this is an 82 454 in my motorhome. when i bought it the fan belt was squeeling a little. week later it bailed. bought a new one and discovered two spares in the motorhome parts bin?? replace it squeel went away mostly. lasted a week. 100 miles went bye bye....replaced alternater. looked...

Can i get a GPS/ Backup camera setup that uses one monitor on the dash i could switch back and forth as needed? I want both but would rather have only one 7 inch screen. Anyone know a lot about these things as i have existing wires everywhere and dont know what most of em do or did? i could...

Can you do it? I just bought a motor home (KOH Baby:awesomework:) and it has an existing roof mounted antennea, that someone cut the cable end off under the dash. I want to use this antennea if possible but i would have to disassemble the entire interior to get to the inside of the roof mount...

I have a chance to take the willys out for its first dirt run. Anyone want to meet there and take me around that knows the place somewhat. It has changed a ton since I was last there.:redneck: Plan on being at the parking lot around 10:30ish.:awesomework:

i need 120 ML of 5W Amsoil suspention oil for a bumpstop? anyone have any or know where i can get some oil, semi close to everett?

so i searched and didnt find a thread talking about air lines and fittings for the ARB air locker. i hate the cheesy plastic lines and brass fittings that are part of the differential bulkhead fittings. so what do you all use? i am attempting to make my own setup that uses 37Degree JIC...

I thought i had the correct 80s ford sixty housing which was the first piece i collected. it was free. so i ordered all 35 spline ****. guess the rear spindles need to be bored afterall:mad: so who can do it? any suggestions about doing it myself?

ok i have a morphed front 60. it started life as a 99 dodge 2500 unit bearing. i retubed the long side and cut the short side to make it 80 size dodge or chevy.... the long side tube was machined for a seal area when installed. so the new 35 spline seals fit right in. the short side...

Do you think the massive flooding and rainfall happening down there now will have an affect on the race course and or layout? last year the course went right thru the lakebed and its was so wet two days before you could not drive on it. it was fine on rae day. Apple valley has had an...

Alternator is not putting out. i have a known good alternator, has a plug to the side and a red wire with fuseable link coming off the back. the engine harness comes with a 4 pin plug with one wire that plugs into the plug. the chassis harnesss has two wires; big red for back output white...

stolen from pirate: http://www.pirate4x4.com/forum/showthread.php?t=922356 anyone have any input or idea where in everett? indoors or outdoors? im assuming man made course? i believe there was talk about this last year or something. somebody knows something spill it.....:cheer:

I need to find some ends for wires i can put into existing plugs. i want the automotive type that come from the factory like these exactly for a 14 Ga wire? i want to just put these ends on my harness wires and put them into the plugs and not use butt connectors mon the wires.. source...